Bedienungsanleitung Trotec PAC3000 XA plus (Seite 13 von 27) (Englisch)

727660

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

EN 13

local air conditioner PAC 3500 SH / PAC 3000 X A+

Setting the timer

The timer has two modes of operation:

• automatic switch-on upon expiry of a preset number of

hours.

• automatic switch-off upon expiry of a preset number of

hours.

This setting can be made at the device or using the remote

control.

Automatic switch-on and automatic switch-off may be enabled

at the same time. The timer LEDs(13) on the control panel will

then be illuminated simultaneously. When using the remote

control for setting, TIMER ON and TIMER OFF(36) will

additionally be indicated on the display(30) simultaneously.

The function can be set in all operating modes and also during

stand-by.

The number of hours can be set in increments

of 0.5hours (0h to 10h) or in increments

of 1hour (10h to 24h).

Note

Do not leave the operating device unattended in a

freely accessible room with an activated timer.

Automatic switch-on

ü The device is switched off.

1. Press the Timer button(27) until the timeron LED(13) is

illuminated.

2. Set the desired number of hours by use of the Increase

value(24) and Decrease value(25) buttons.

ð The number of hours will be indicated on the segment

display(16) for approx. 5s.

ð The timer setting equals the desired number of hours.

ð After the predefined time, the device switches itself on.

Notes regarding automatic switch-on:

• If the device is disconnected from the power supply, all

settings for automatic switch-on are deleted.

• Manually switching the device on disables the automatic

switch-on function.

• If you select 0.0hours, the timer will be off.

Automatic switch-off

ü The device is switched on.

1. Press the Timer button(27) until the timeroff LED(13) is

illuminated.

2. Set the desired number of hours by use of the Increase

value(24) and Decrease value(25) buttons.

ð The number of hours will be indicated on the segment

display(16) for approx. 5s.

ð The timer setting equals the desired number of hours.

ð After the predefined time, the device switches itself off.

Notes regarding automatic switch-off:

• Pressing the On/ Off button(21) deactivates the automatic

switch-off function.

Night mode

Night mode can be activated in cooling or heating mode and

during automatic operation.

Night mode comes with the following settings:

• After 1hour the preset temperature is increased or

reduced by 1°C. After another 30minutes the preset

temperature will again be increased or reduced by 1°C.

Then the temperature is kept constant for 7hours before

the device sets the original temperature automatically.

• In automatic mode, the fan speed is preset to the lowest

stage and cannot be adjusted. In cooling mode, the fan

speed can be changed, which disables night mode.

To activate night mode, please proceed as follows:

1. Select cooling mode, heating mode or automatic operation.

2. Press the Sleep button(22).

ð The operating mode(14) and sleep LEDs(20) are

illuminated.

3. In order to switch the night mode off, press the Sleep

button(22) once again.

ð The sleep LED(20) turns off.

ð The selected operating mode remains active.

Swing function

The swing function can be switched on in any operating mode

if required.

By means of the swing function, the air outlet(2) is moved

automatically and thus ensures continuous air circulation.

1. Press the Swing button(28).

ð The ventilation flaps move up and down continuously.

2. Press the Swing button(28) again to stop the ventilation

flaps in a certain position and to switch off the swing

function.

Changing the unit °C / °F

The temperature in the segment display(16) can be

indicated in °C or °F.

Please proceed as follows to change the temperature unit:

1. Simultaneously press and hold the Increase value(24) and

Decrease value(25) buttons for approx. 3s.

ð The displayed temperature is converted to the other

unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAC3000 XA plus Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAC3000 XA plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info