Bedienungsanleitung Trotec PAC3500SH (Seite 14 von 24) (Englisch)

689433

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

14 EN

local air conditioner PAC 3500 SH

Switching the LEDs on the control panel on or off

The control panel illumination at the devices can be switched on

and off.

This setting can only be made using the remote control.

1. Press the LED button(34).

ð The LEDs and the segment display(16) on the control

panel will be switched off.

ð The device continues to run with the selected settings.

2. Press the LED button(34) again.

ð The LEDs and the segment display(16) on the control

panel will be switched back on.

FollowMe function

This setting can only be made using the remote control.

Using the FollowMe function, the remote control measures the

temperature at your current location. The degree of cooling and

heating is controlled by the air conditioner based on the

measured temperature.

The FollowMe function can be activated in cooling or heating

mode and during automatic operation.

1. Press the FOLLOWME button(35).

ð The FOLLOWME indication(39) appears on the

display(30).

ð The FollowMe LED(15) is illuminated.

ð The remote control sends a temperature signal to the air

conditioner every 3minutes.

2. Press the FOLLOWME button(35) again to disable the

FollowMe function.

Memory function

After a power failure during operation the device will

automatically be switched back on. The chosen operating mode

settings will be saved, a possibly programmed timer will not.

All the chosen settings (incl. timer) remain saved on the remote

control. As soon as the device receives an input from the remote

control, the settings will be transmitted from the remote control

to the device.

The compressor may start up with a delay of 3min, as it is

provided with an internal protection against direct restart.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the condensation tray if necessary.

• If necessary, remove the condensation drain hose and any

residual fluid from it.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• Observe the operating temperature according to the

Technical data chapter.

• The condensation tray may be full. Empty the condensation

tray if necessary. The error codeP1 must not be indicated

on the segment display.

• Wait for 10minutes before restarting the device. If the

device is not starting, have the electrics checked by a

specialist company or by Trotec.

The device works with reduced or no cooling capacity:

• Check whether cooling mode is selected.

• Check the proper fit of the exhaust air hose. In case of

kinks, bends or blockage in the hose, exhaust air cannot

be discharged. Clear the way for the exhaust air.

• Check the position of the ventilation flaps. They should be

opened to the maximum.

• Check the air filter(s) for dirt. If necessary, clean or replace

the air filter(s).

• Check the minimum distance to walls or other objects.

Position the device a little more in the room's centre

if required.

• Check whether any windows and/or doors of the room are

open. If so, close them. One window has to remain open

for the exhaust air hose nonetheless.

• Check the temperature setting at the device. Reduce the

set temperature if it is higher than the room temperature.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright

position.

Condensate is leaking:

• Check the device for leaks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAC3500SH Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAC3500SH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info