Bedienungsanleitung Trotec PAE26 (Seite 14 von 21) (Englisch)

728000

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

13 EN

air cooler PAE 26

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• Check whether the overheating protection has tripped (see

chapter Operation).

• Wait for 10minutes before restarting the device. If the

device is not starting, have the electrics checked by a

specialist company or by Trotec.

The device has automatically switched itself off:

• Keep the air inlet clear to prevent the motor from

overheating.

• Check whether the overheating protection has tripped (see

chapter Operation).

The device works with reduced or no capacity:

• Check the position of the horizontal ventilation flaps. They

should be opened to the maximum.

• Check the air filter for dirt. If necessary, clean or replace

the air filter.

• Check the minimum distance to walls or other objects.

Position the device a little more in the room's centre if

required.

The device is running, but there is no air cooling or pump

operation:

• Check whether air cooling mode is activated. The Humidify

LED(21) should be illuminated.

• Check the filling level of the water tank (see chapter Filling

the water tank). The Humidify LED(21) should not flash.

• Check whether there are any objects blocking the pump

inlet. Make sure that the pump inlet is not blocked.

• In case the pump does not operate despite a correctly filled

water tank and activated air cooling mode, the pump might

be defective. Please contact the customer service.

Water is leaking:

• Check the device for leaks.

• Check the water tank for tight fit.

The water tank cannot be inserted

• Check whether the mechanism for lowering the pump was

released. If the pump can be seen in the lower area, the

water tank is being blocked.

– Push the pump up until the switch for lowering the

pump can be seen.

The swing function is not working:

• The swing function motor might be defective. Please

contact the customer service.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright

position.

The device does not respond to the infrared remote control:

• Check whether the distance between remote control and

device is too large and reduce it if necessary.

• Make sure there are no obstacles, such as furniture or

walls, between the device and the remote control. Ensure

visual contact between device and remote control.

• Check the charging status of the batteries and change

them if required.

• If the batteries have only just been changed, check them

for correct polarity and change them if required.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAE26 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAE26

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info