Bedienungsanleitung Trotec PAGS 10-230 (Seite 6 von 20) (Englisch)

753916

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

6 EN

angle grinder PAGS 10-230

•Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel. Proper

wheel flanges support the wheel thus reducing the

possibility of wheel breakage. Flanges for cut-off wheels

may be different from grinding wheel flanges.

•Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the

higher speed of a smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive

Cutting-Off Operations

•Do not "jam" the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

•Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation,

is moving away from your body, the possible kickback may

propel the spinning wheel and the power tool directly at

you.

•When wheel is binding or when interrupting a cut for

any reason, switch off the power tool and hold the

power tool motionless until the wheel comes to a

complete stop. Never attempt to remove the cut-off

wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheel binding.

•Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

•Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the line

of cut and near the edge of the workpiece on both sides of

the wheel.

•Use extra caution when making a "pocket cut" into

existing walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects

that can cause kickback.

Safety Warnings Specific for Wire Brushing

Operations

•Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush. The wire

bristles can easily penetrate light clothing and/or skin.

•If the use of a guard is recommended for wire

brushing, do not allow any interference of the wire

wheel or brush with the guard. Wire wheel or brush may

expand in diameter due to work load and centrifugal

forces.

Device-specific safety warnings for angle grinders

•Use suitable detectors to determine if utility lines are

hidden in the work area or call the local utility

company for assistance. Contact with electrical lines

may result in fire and electric shock. Damaging a gas line

may lead to an explosion. Penetrating a water line causes

property damage and may cause an electric shock.

•If the power supply is interrupted, e.g. due to a power

failure or because the mains plug has been pulled out,

unlock the on/off switch and set it to the off position.

This is done to prevent uncontrolled restart.

•Do not touch the abrasive wheels and cutting discs

until they have cooled down. The wheels and discs

become very hot during operation.

•Secure the workpiece. The grip of tensioning devices or a

vice is more secure than holding the workpiece only by

hand.

Intended use

Only use the device PAGS 10-230:

• for cutting, grinding and brushing metal as well as stone

materials without the use of water.

• for cutting tiles and concrete blocks. When cutting stone,

an adequate dust extraction system must be provided.

We recommend using the power tool with original Trotec

accessories.

Foreseeable misuse

• Operations such as polishing are not recommended to be

performed with this power tool.

• Do not use accessories that require liquid coolants.

• Do not use this power tool for processing wood.

Any other use than the one described in the chapter "Intended

use" is regarded as reasonably foreseeable misuse.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAGS 10-230 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAGS 10-230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info