Bedienungsanleitung Trotec PAGS 10-230 (Seite 10 von 20) (Englisch)

753916

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

10 EN

angle grinder PAGS 10-230

Technical data

Parameter Value

Model PAGS10-230

Mains connection 1/N/PE ~ 230 V/ 50 Hz

Power consumption 2 kW

Rated speed 6,500rpm

Spindle thread M14

Maximum disc diameter 230 mm

Cable length 4 m

Protection class II /

Weight 6 kg

Cutting disc (scope of delivery)

Idle speed cutting disc 6,600rpm

Disc speed 80 m/s

Bore diameter 22.23 mm

Cutting disc thickness 3 mm

Vibration information according to EN 60745

Vibration emission value main

handle ah7.4 m/s²

Vibration emission value

additional handle ah14.1 m/s²

Uncertainty K main handle /

additional handle 1.5 m/s²

Sound values according to EN 60745

Sound pressure level LpA 91 dB(A)

Sound power LWA 102 dB(A)

Uncertainty K 3 dB

Wear hearing protection.

Excessive noise can lead to hearing loss.

Information on noise and vibration:

• The vibration level specified in these instructions was

determined by means of a measuring method standardized

in EN60745 and can be used for a device comparison. The

specified vibration emission value may also be used for a

preliminary assessment of the exposure.

Caution

Vibration emissions can cause a health hazard if the

device is used for an extended period of time or if it is

not properly handled and maintained.

• The vibration level will change depending on the

application of the power tool and may in some cases differ

from the value specified in these instructions. The vibration

load may be underestimated if the power tool is used

regularly in such a way. For a precise estimation of the

vibration load during a certain work period, it is also

important to consider the periods during which the device

is switched off, or is running but not actually employed.

This can reduce the vibration load over the entire work

period significantly.

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

For transporting the device, use the transport case included in

the scope of delivery in order to protect the device from external

influences.

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down.

• Remove the tool from the tool holder.

Storage

Before storing the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down.

• Remove the tool from the tool holder.

• Clean the device as described in the Maintenance chapter.

• For storing the device, use the transport case included in

the scope of delivery in order to protect the device from

external influences.

When the device is not being used, observe the following

storage conditions:

• Dry and protected from frost and heat

• Ambient temperature below 45°C

• Protected from dust and direct sunlight inside the transport

case

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAGS 10-230 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAGS 10-230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info