Bedienungsanleitung Trotec PBSS 10-600 (Seite 8 von 18) (Englisch)

753918

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

8 EN

belt sander PBSS 10-600

Technical data

Parameter Value

Model PBSS 10-600

Mains connection 1/N/PE ~ 230–240 V/

50Hz

Power input 600 W

Belt speed 170–250m/min

Idle speed 1,450 – 2,120 rpm

Dimensions of the abrasive belt

(width x length)

75x457mm

Grinding surface 75x130mm

Cable length 4 m

Protection class II /

Weight 2 kg

Vibration information according to EN62841-2-4

Vibration emission value main

handle ah

1.863 m/s²

Vibration emission value front

handle ah

2.399 m/s²

Uncertainty K 1.5 m/s²

Sound values according to EN62841-2-4

Sound pressure level LpA 88.6dB(A)

Sound power LWA 99.6dB(A)

Uncertainty K 3 dB

Wear hearing protection.

Excessive noise can lead to hearing loss.

Information on noise and vibration:

• The specified total vibration and noise emission values

were measured by means of a test procedure standardized

in EN62841 and can be consulted for the comparison of

one power tool with another.

• The specified total vibration and noise emission values

can also be used for preliminary load assessment.

Caution

Vibration emissions can cause a health hazard if the

device is used for an extended period of time or if it is

not properly handled and maintained.

• The actual vibration and noise emission may differ from

the stated values during operation of the power tool. This

depends on how the power tool is used and especially on

the type of workpiece being processed. Try to keep the

vibration load to a minimum. Exemplary measures for

reducing the vibration load include wearing gloves during

operation of the tool and the limitation of working hours.

All parts of an operating cycle must be considered for this

(e.g. times at which the power tool is switched off and

times when it is switched on but runs without load).

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down.

• If attached, disconnect the dust extraction system from the

device.

Storage

Before storing the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down.

• If attached, disconnect the dust extraction system from the

device.

• Clean the device as described in the Maintenance chapter.

When the device is not being used, observe the following

storage conditions:

• Dry and protected from frost and heat

• Ambient temperature below 45°C

• protected from dust and direct sunlight

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PBSS 10-600 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PBSS 10-600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info