Bedienungsanleitung Trotec PCSS 05-20V (Seite 15 von 20) (Englisch)

753908

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

EN 15

mini cordless portable circular saw PCSS 05-20V

Operation

Tips and notes on handling the circular saw

General information:

• Keep the venting slots clear to prevent the motor from

overheating.

• Only use intact, flawless saw blades. Saw blades can be

damaged by shocks or impacts. Bent, blunt or otherwise

damaged saw blades could break. The sawing

performance and cutting quality essentially depend on the

saw blade's condition and the shape of the teeth.

• Check the saw blade for correct fit before every

application.

• Before every application, make sure that you have selected

the correct saw blade for the intended use.

• Before every application, check whether you need a dust

bag or dust extraction system.

– Harmful dusts are produced when processing wood,

particularly beech and oak. Beech and oak dust is

considered carcinogenic, especially in combination with

certain wood treatment additives such as chromate or

wood preservatives. Wear a protective mask.

– Dusts from materials containing leaded paint or

minerals can be harmful to health. Wear a protective

mask.

– Long, spiral chips are produced when processing

spruce.

• The falling part of the workpiece should be located on the

right-hand side of the power tool so that the larger part of

the workpiece remains in full contact with the supporting

table or similar.

• Guide the power tool by pushing slightly and evenly in the

cutting direction. Pushing too hard reduces the blade life

and can damage the power tool.

• If you are sawing along a drawn line, guide the power tool

along the respective notch.

• Tear-out of the edges cut into sensitive surfaces (e.g.

plasterboard or coated chipboard) can be prevented by

covering the cutting edges with masking tape. In this case,

the cutting line can also be drawn on the masking tape to

protect the workpiece surface.

• Non-coated saw blades can be protected against corrosion

by applying a thin layer of acid-free oil. Remove any oil

before starting to saw to prevent oil residues from reaching

the wood.

• When sawing lightweight construction materials, observe

the legal regulations and recommendations of the material

manufacturers.

Sawing wood:

• Before sawing wood, chipboards, building materials etc.,

check the above for foreign objects, e.g. nails, screws or

similar. If required, remove the foreign objects or use a

suitable, sharp saw blade.

• The choice of the saw blade depends on the type of

application (longitudinal or cross cuts) as well as the type

and quality of wood.

• If the saw blade gets jammed in the workpiece, switch off

the power tool immediately. The sawing gap should be

slightly widened with a suitable tool so that you can pull

out the power tool.

• Switch on the power tool and guide it towards the

workpiece to be processed. Place the guide shoe on the

surface of the workpiece. Process the workpiece with an

even forward motion and contact pressure. After

completing the sawing operation, switch off the power

tool.

Sawing non-ferrous metals:

• Metal dusts can be harmful to health. Wear a protective

mask.

• Only use a sharp saw blade suitable for non-ferrous

metals. This guarantees a clean cut and prevents the saw

blade from getting jammed.

• Only hold the power tool against the workpiece when the

tool is switched on and running. Start sawing carefully and

with little forward motion. Continue sawing with little

forward motion and without interrupting.

• When sawing narrow profiles, you should start on the

narrow side. When sawing U-profiles, you should start on

the open side. Long profiles should be supported to

prevent the saw blade from getting jammed and thus to

avoid the risk of a kickback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PCSS 05-20V Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PCSS 05-20V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info