Bedienungsanleitung Trotec PCSS 10-20V (Seite 18 von 24) (Englisch)

753909

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

18 EN

cordless portable circular saw PCSS 10-20V

Checking the pendulum guard

The pendulum guard is an important safety device of the power

tool. It must function properly; otherwise the device must not be

used.

Observe the following information:

Safety warnings for circular saws with pendulum guard

and circular saws with tow guard – Lower guard function

•Check the lower guard for proper closure before each

use. Do not operate the saw if the lower guard does

not move freely and close immediately. Never clamp or

tie the lower guard in the open position.

The lower guard may be bent if the saw accidentally falls

to the floor. Use the retracting lever to raise the guard and

make sure that it moves freely and does not touch the

blade or any other part of the saw at all cutting angles and

depths of cut.

•Check that the lower guard spring operates correctly.

If the guard and spring do not operate correctly, have

the saw serviced before use.

Lower guard may operate sluggishly due to damaged

parts, gummy deposits, or a build-up of debris.

•Lower guard may be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts". Raise lower guard by retracting lever and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

•Always observe that the lower guard is covering the

blade before placing saw down on bench or floor.

An unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Operation

Tips and notes on handling the circular saw

General information:

• Keep the venting slots clear to prevent the motor from

overheating.

• Only use intact, flawless saw blades. Saw blades can be

damaged by shocks or impacts. Bent, blunt or otherwise

damaged saw blades could break. The sawing

performance and cutting quality essentially depend on the

saw blade's condition and the shape of the teeth.

• Check the saw blade for correct fit before every

application.

• Before every application, make sure that you have selected

the correct saw blade for the intended use.

• Before every application, check whether you need a dust

bag or dust extraction system.

– Harmful dusts are produced when processing wood,

particularly beech and oak. Beech and oak dust is

considered carcinogenic, especially in combination with

certain wood treatment additives such as chromate or

wood preservatives. Wear a protective mask.

– Dusts from materials containing leaded paint or

minerals can be harmful to health. Wear a protective

mask.

– Long, spiral chips are produced when processing

spruce.

• The falling part of the workpiece should be located on the

right-hand side of the power tool so that the larger part of

the workpiece remains in full contact with the supporting

table or similar.

• Guide the power tool by pushing slightly and evenly in the

cutting direction. Pushing too hard reduces the blade life

and can damage the power tool.

• If you are sawing along a drawn line, guide the power tool

along the respective notch.

• Tear-out of the edges cut into sensitive surfaces

(e.g. plasterboard or coated chipboard) can be prevented

by covering the cutting edges with masking tape. In this

case, the cutting line can also be drawn on the masking

tape to protect the workpiece surface.

• Non-coated saw blades can be protected against corrosion

by applying a thin layer of acid-free oil. Remove any oil

before starting to saw to prevent oil residues from reaching

the wood.

• When sawing lightweight construction materials, observe

the legal regulations and recommendations of the material

manufacturers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PCSS 10-20V Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PCSS 10-20V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info