Bedienungsanleitung Trotec PJSS10-230V (Seite 8 von 19) (Englisch)

753370

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

7 EN

Operating manual – 850W pendulum action jigsaw PJSS 10-230V

Technical data

Parameter Value

Model PJSS10-230V

Mains connection 1/N/PE ~ 230 V / 50 Hz

Power consumption 0.85 kW

Idle speed 0 – 3,000 spm

Cutting angle 0° / 15° / 30° / 45°

Cable length 3 m

Protection class II /

Weight 2 kg

Vibration information according to EN60745

Total vibration emission value:

Sawing chipboards ah,B

Uncertainty K

9.5 m/s²

1.5 m/s²

Sawing sheet metal ah,B

Uncertainty K

11.2 m/s²

1.5 m/s²

Sound values according to EN60745

Sound pressure level LpA 88 dB(A)

Sound power LWA 99 dB(A)

Uncertainty K 3 dB

Wear hearing protection.

Excessive noise can lead to hearing loss.

Information on noise and vibration:

• The vibration level specified in these instructions was

determined by means of a measuring method standardized

in EN60745 and can be used for a device comparison. The

specified vibration emission value may also be used for a

preliminary assessment of the exposure.

Caution

Vibration emissions can cause a health hazard if the

device is used for an extended period of time or if it is

not properly handled and maintained.

• The vibration level will change depending on the

application of the power tool and may in some cases differ

from the value specified in these instructions. The vibration

load may be underestimated if the power tool is used

regularly in such a way. For a precise estimation of the

vibration load during a certain work period, it is also

important to consider the periods during which the device

is switched off, or is running but not actually employed.

This can reduce the vibration load over the entire work

period significantly.

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down.

• Remove the tool from the tool holder.

• If attached, disconnect the dust extraction system from the

device.

Storage

Before storing the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down.

• Remove the tool from the tool holder.

• If attached, disconnect the dust extraction system from the

device.

• Clean the device as described in the Maintenance chapter.

When the device is not being used, observe the following

storage conditions:

• dry and protected from frost and heat

• ambient temperature below 40 °C

• protected from dust and direct sunlight

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PJSS10-230V Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PJSS10-230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info