Bedienungsanleitung Trotec PJSS10-230V (Seite 16 von 19) (Englisch)

753370

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

15 EN

Operating manual – 850W pendulum action jigsaw PJSS 10-230V

The saw blade experiences difficulties penetrating the

material to be processed or the sawing performance is

insufficient:

• Check the set stroke rate; it must be suitable for both the

saw blade and the material.

• To select a higher stroke rate, turn up the setting wheel for

stroke rate selection.

• Check whether the pendulum action setting is suitable for

the material to be processed.

• If the saw blade is worn, replace it with a new one.

• Check whether the chosen saw blade is suitable for the

material to be processed.

The device becomes hot:

• Make sure not to exert too much pressure on the device

during sawing.

• To select a low stroke rate, turn down the setting wheel for

stroke rate selection.

• Check whether the chosen saw blade is suitable for the

task to be carried out.

• Keep the venting slots clear to prevent the motor from

overheating.

Info

Wait for at least 10 minutes before switching the

device back on.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Maintenance tasks which require the housing to be

opened must only be carried out by authorised

specialist companies or by Trotec.

Notes on maintenance

Inside the device, there are no parts that need to be maintained

or lubricated by the user.

Cleaning

The device should be cleaned before and after each use.

Note

The device does not have to be lubricated after

cleaning.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids

penetrating the housing!

Do not immerse the device and the accessories in

water. Make sure that no water or other liquids can

enter the housing.

• Clean the device with a soft, damp and lint-free cloth.

Ensure that no moisture enters the housing. Protect

electrical components from moisture. Do not use any

aggressive cleaning agents such as cleaning sprays,

solvents, alcohol-based or abrasive cleaners to dampen

the cloth.

• Dry the device with a soft, lint-free cloth.

• Dry the saw blades with a soft, lint-free cloth.

• Remove any dust deposits and, if applicable, wood chips

or material residues from the quick-release chuck.

• Keep the ventilation openings free from dust deposits to

prevent overheating of the motor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PJSS10-230V Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PJSS10-230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info