Bedienungsanleitung Trotec PMTS01-230V (Seite 4 von 21) (Englisch)

753364

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

4 EN

170W multi-function tool PMTS 01-230V

•Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tool's operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

•Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

•Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

•Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

General Power Tool Safety Warnings– Service

•Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety warnings for multi-function tools

•Hold the power tool by its insulated gripping surfaces

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Contacting a live wire might energize exposed metal parts

of the device and lead to an electric shock.

•Only use the power tool for dry sanding. Water entering

an electrical appliance increases the risk of electric shock.

•Keep your hands out of the sawing area. Do not reach

underneath the workpiece. Risk of injury upon contact

with the saw blade.

•Use appropriate detection equipment to track down

concealed supply lines or consult the local utility

companies. Contact with electrical lines may result in fire

and electric shock. Damaging a gas line may lead to an

explosion. Penetrating a water line causes property

damage and may cause an electric shock.

•During operation hold onto the power tool with both

hands and make sure you stand firmly on the ground.

It is safer to handle the power tool with two hands.

•Secure the workpiece. The grip of tensioning devices or a

vice is more secure than holding the workpiece only by

hand.

Wear protective gloves when changing the insertion

tools. The applied tools heat up during longer

operation.

•Do not treat the surface to be processed with liquids

containing solvents. Toxic fumes may be produced

during scraping owing to the heat-up of the materials.

•Ensure sufficient ventilation when processing plastics,

paints, varnishes etc.

•Wait until the device has come to a standstill, before

putting it down.

Safety Warnings Specific for Grinding and Abrasive

Cutting-Off Operations

•Use only the abrasive products recommended for your

power tool and only for the recommended

applications. Example: do not grind with the side of

cut-off wheel. Cutting discs are designed for material

removal using the edge of the disc. Exerting force to the

sides of these abrasives may break them.

•For conical and straight abrasive pencils with a thread,

only use undamaged mandrels of the correct size and

length without an undercut on the shoulder. Suitable

mandrels prevent the risk of breakage.

•Do not "jam" the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

•Do not position your hand in line with and behind the

rotating cutting wheel. When the wheel, at the point of

operation, is moving away from your hand, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

•When wheel is binding or when interrupting a cut for

any reason, switch off the power tool and hold the

power tool motionless until the wheel comes to a

complete stop. Never attempt to remove the cut-off

wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheel binding.

•Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

•Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the line

of cut and near the edge of the workpiece on both sides of

the wheel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PMTS01-230V Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PMTS01-230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info