Bedienungsanleitung Trotec PMTS10 - 12V (Seite 14 von 22) (Englisch)

689479

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

13 EN

cordless multi-function tool PMTS 10-12V

Operation

Tips and notes on handling the multi-function tool

General information:

• Keep the venting slots clear to prevent the motor from

overheating.

• Check the tool in the tool holder for proper fit before every

application. The tool must be firmly locked in place in the

designated holding fixtures in the tool holder.

• Before every application, make sure that you have selected

the correct tool for the intended use.

Sawing:

• Only use intact, flawless saw blades. Bent, blunt or

otherwise damaged saw blades could break.

• When sawing lightweight construction materials, make

sure to observe the legal regulations and

recommendations of the material manufacturers.

• Only soft materials such as plasterboard or the like may be

processed using the plunge-cutting method!

• Before sawing wood, chipboards, building materials etc.

with HCSblades, check the above for foreign objects, e.g.

nails, screws or similar. If required, remove the foreign

objects or use bi-metal saw blades.

• Use a narrow saw blade when sawing tight curves.

• The saw blade should not be longer than required for the

intended cut.

Cutting:

• Only use intact, flawless cutting blades. Bent, blunt or

otherwise damaged cutting blades could break.

• When cutting wall tiles, bear in mind that the insertion

tools are subjected to a high level of wear during longer

operation.

Scraping:

• Choose a high oscillation rate for scraping.

• On soft ground (e.g. wood) work at a shallow angle and

with only little contact pressure. Otherwise the scraping

knife could cut into the ground.

Sanding:

• Maintain a consistent grinding pressure to increase the

lifetime of the sanding sheets.

• Choose from the different sanding sheets (red for wood,

black for metal) in due consideration of the material to be

processed and the desired surface abrasion.

• Avoid the accumulation of dust at the workplace, always

use a dust extraction system when grinding.

• Use the coarse triangular sanding sheets (e.g. 60 grit) for

rough grinding and the fine ones (e.g. 240 grit) for fine and

finish grinding.

Switching the device on and off

Wear your personal protective equipment when working with

the device.

1. Check whether the fixed tool and the set oscillation rate

are suitable for the intended application.

2. Check whether the workpiece is secured and the worktop

prepared correspondingly.

3. To switch the device on, push the on/off switch(2)

forward so that the I becomes visible.

ð The LED work lamp is illuminated.

4. To switch the device off, push the on/off switch(2) to the

rear so that the 0 becomes visible.

ð The LED work lamp goes out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PMTS10 - 12V Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PMTS10 - 12V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info