Bedienungsanleitung Trotec PMTS10 - 230V (Seite 15 von 19) (Englisch)

689480

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

EN 14

300W multi-function tool PMTS 10-230V

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Slight smoke or odour are emitted during first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

Info

Wait for at least 10 minutes before switching the

device back on.

The tool is loose:

• Make sure that the tool is firmly locked in place in the

designated recesses of the tool holder.

• Make sure that the clamping screw at the tool holder is

tightened properly.

• Make sure that the tool release lever is folded back

completely.

The saw blade experiences difficulties plunge-cutting the

material to be processed or the sawing/grinding

performance is insufficient:

• Check the set oscillation rate, it must be suitable for both

the tool and the material.

• To select a higher oscillation rate, turn up the setting

wheel for oscillation rate selection.

• If the saw blade is worn, replace it with a new one.

• Check whether the chosen tool is suitable for the material

to be processed.

The device becomes hot:

• Make sure not to exert too much pressure on the device

during grinding.

• Select a low oscillation rate by turn down the setting wheel

for oscillation rate selection(3).

• Check whether the tool is suitable for the tasks to be

carried out.

• Keep the venting slots clear to prevent the motor from

overheating.

• Wait for at least 10 minutes before switching the device

back on.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Maintenance tasks which require the housing to be

opened must only be carried out by authorised

specialist companies or by Trotec.

Notes on maintenance

Inside the device, there are no parts that need to be maintained

or lubricated by the user.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PMTS10 - 230V Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PMTS10 - 230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info