Bedienungsanleitung Trotec PMTS10-20V (Seite 18 von 21) (Englisch)

753363

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

18 EN

cordless multi-function tool PMTS 10-20V

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Light smoke or odour is emitted during the first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The battery does not charge:

• Check whether the battery is inserted correctly in the quick

charger.

Slide the battery into the quick charger in a way that the

battery terminals engage in the quick charger. The battery

must lock in place in the quick charger.

• Check the power connection.

• Check the power cable and mains plug for damage.

• Check the on-site fusing.

• Check the quick charger for damage. If the quick charger

is damaged, stop using it. Contact the Trotec customer

service.

• Check the battery terminals for dirt. Remove any dirt.

• The battery might be defective and have to be replaced.

Only use batteries of the same type.

The device does not start:

• The battery power might be too low. Recharge the battery.

• Check whether the battery is correctly connected to the

device.

Slide the battery onto the device in a way that the battery

terminals engage. The battery must lock in place in the

device.

• Check the battery terminals for dirt. Remove any dirt.

Info

Wait for at least 10 minutes before switching the

device back on.

The device becomes hot:

• Make sure not to exert too much pressure on the device

during grinding.

• Select a low oscillation rate by turn down the setting wheel

for oscillation rate selection(3).

• Check whether the tool is suitable for the tasks to be

carried out.

• Keep the venting slots clear to prevent the motor from

overheating.

Info

Wait for at least 10 minutes before switching the

device back on.

The tool is loose:

• Make sure that the tool is firmly locked in place in the

designated recesses of the tool holder.

• Make sure that the clamping screw at the tool holder is

tightened properly.

• Make sure that the tool release lever is folded back

completely.

The saw blade experiences difficulties plunge-cutting the

material to be processed or the sawing/grinding

performance is insufficient:

• Check the set oscillation rate, it must be suitable for both

the tool and the material.

• To select a higher oscillation rate, turn up the setting

wheel for oscillation rate selection 3.

• If the saw blade is worn, replace it with a new one.

• Check whether the chosen tool is suitable for the material

to be processed.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorised specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PMTS10-20V Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PMTS10-20V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info