Bedienungsanleitung Trotec PRCS 10-20V (Seite 5 von 21) (Englisch)

753905

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

EN 5

cordless sabre saw PRCS 10-20V

•Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

workpiece by your hand or against the body leaves it

unstable and may lead to loss of control.

•Vibrations can be harmful to the human hand-arm

system. Keep the vibration exposure time to a minimum.

•Clean the shank of the saw blade before inserting it. A

dirty shank cannot be fastened securely.

•Check the saw blade for tight fit. A loose saw blade

could fall out and injure you.

•Before switching on the power tool, ensure that the

insertion tool can move freely. If the device is switched

on with a jammed insertion tool, the resulting forces can

be extreme causing the device to kick out sideways.

•Do not work on moistened material or moist surfaces.

•Only hold the power tool against the workpiece when

the tool is switched on and running. Otherwise there is

a risk of kickbacks.

•Make sure that the guide shoe is positioned securely

on the contact face during sawing. A jammed saw blade

could break or cause a kickback.

•Keep your hands out of the sawing area. Do not reach

underneath the workpiece. Risk of injury upon contact with

the saw blade.

•Keep your hands away from lifting rod and quick-

release chuck. Crushing hazard upon contact with these

components.

•Ensure sufficient ventilation.

•Regularly check the quick-release chuck for wear or

damage.

•Only use intact, flawless saw blades. Bent and blunt

saw blades could break or cause a kickback.

•Do not attempt to slow down the saw blade movement

by pressing against the blade from the side once the

device is switched off. The saw blade could be damaged,

break or cause a kickback.

•Switch off the power tool when your operation is

completed, but do not remove the saw blade from the

kerf until it has come to a standstill. This serves to

avoid a kickback, then you can put the power tool down

safely.

•Immediately switch off the power tool if the insertion

tool blocks. The power tool can lash out to the side owing

to the forces that build up consequently.

•Wait until the power tool has come to a standstill,

before putting it down. The insertion tool could get

caught resulting in a loss of control of the power tool.

Safety warnings for reciprocating saws

•Hold the power tool by its insulated gripping surfaces

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting a "live" wire may make exposed metal parts of the

power tool "live" and could give the operator an electric

shock.

•Use clamps or another practical way to secure and

support the workpiece to a stable platform.

Holding the workpiece by your hand or against the body

leaves it unstable and may lead to loss of control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PRCS 10-20V Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PRCS 10-20V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info