Bedienungsanleitung Trotec PRDS05-230V (Seite 16 von 18) (Englisch)

753296

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

16 EN

rotary hammer PRDS 05-230V

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Light smoke or odour is emitted during the first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages. If you

notice damages, do not try to take the device back into

operation. To avoid safety hazards, do not perform any

repairs. Send the device to a specialist electrical company

or to Trotec to have the power cable and mains plug

replaced.

• Check whether the clockwise/ counter-clockwise rotation

switch(10) is in centre position. Select a rotational

direction that is suitable for the intended application.

• Check the on-site fusing.

Info

Wait for at least 10 minutes before switching the

device back on.

The drill bit does not penetrate / hardly penetrates the

material:

• The setting for drilling or impact drilling should

be selected.

• Check whether the correct drill bit is selected.

• Check whether the function selector switch(3) is set to

position . This position is only suitable for chiselling.

• Check whether the device is set to counter-clockwise

rotation. For drilling, it is necessary to switch over to

clockwise rotation.

The chisel does not penetrate / hardly penetrates the

material:

• Check whether you have been working using the correct

speed. A higher speed level may be required in harder

material.

• Check whether the correct tool is selected.

• Check the position of the clockwise/ counter-clockwise

rotation switch(10). The switch must be set to clockwise

rotation.

Info

Wait for at least 10 minutes before switching the

device back on.

The device becomes hot:

• Check whether the tool is suitable for the tasks to be

carried out.

• Keep the venting slots clear to prevent the motor from

overheating.

• Select a lower speed.

Info

Wait for at least 10 minutes before switching the

device back on.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Maintenance tasks which require the housing to be

opened must only be carried out by authorised

specialist companies or by Trotec.

Notes on maintenance

• Slightly grease the tool holder with machine lubricant.

Cleaning

The device should be cleaned before and after each use.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids

penetrating the housing!

Do not immerse the device and the accessories in

water. Make sure that no water or other liquids can

enter the housing.

• Clean the device with a soft, damp and lint-free cloth.

Make sure that no moisture enters the housing. Protect

electrical components from moisture. Do not use any

aggressive cleaning agents such as cleaning sprays,

solvents, alcohol-based or abrasive cleaners to dampen

the cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PRDS05-230V Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PRDS05-230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info