Bedienungsanleitung Trotec PSCS10 - 3.6V (Seite 14 von 18) (Englisch)

689446

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

13 EN

cordless baton screwdriver PSCS 10-3,6V

Available accessories

Warning

Only use accessories and additional equipment

specified in the operating manual.

Using insertion tools or accessories other than those

specified in the operating manual may cause a risk of

injury.

Accessories Article number

Screw bit set, 32-piece 6,200,001,001

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Slight smoke or odour are emitted during first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The battery does not charge:

• Check whether the device is correctly connected to the

charger and whether the charger is correctly connected to

the power supply.

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the fuse (home).

• Check the charger for damages. Should the charger be

damaged, stop using it. Contact the Trotec customer

service.

• Check the charger connection for dirt. Remove any dirt.

• The battery might be defective. Contact the Trotec

customer service.

The device does not start:

• The battery power might be too low. Recharge the battery.

• Check the position of the clockwise / counter-clockwise

rotation switch. The switch must be pressed in all the way.

If the clockwise / counter-clockwise rotation switch is in

centre position (lock), the on / off switch is blocked.

• Check whether the charger is connected. If the charger is

connected, the device will not start.

Info

Wait for at least 10 minutes before switching the

device back on.

The drill bit does not penetrate / hardly penetrates the

material:

• Check whether the correct torque setting is selected. The

drilling setting

should be selected.

• Check whether the device is set to counter-clockwise

rotation. For drilling, it is necessary to switch over to

clockwise rotation.

• Check whether the characteristics of the material require

the use of a hammer drill or impact drill.

The on/off switch cannot be pressed:

• Check whether the clockwise/counter-clockwise rotation

switch is in centre position (lock). Set the desired rotational

direction to unlock the tool.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PSCS10 - 3.6V Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PSCS10 - 3.6V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info