Bedienungsanleitung Trotec PTNS10-20V (Seite 14 von 17) (Englisch)

753360

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

14 EN

cordless tacker PTNS 10-20V

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Light smoke or odour is emitted during the first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The battery does not charge:

• Check whether the battery is inserted correctly in the quick

charger.

Slide the battery into the quick charger in a way that the

battery terminals engage in the quick charger. The battery

must lock in place in the quick charger.

• Check the power connection.

• Check the power cable and mains plug for damage.

• Check the on-site fusing.

• Check the quick charger for damage. If the quick charger

is damaged, stop using it. Contact the Trotec customer

service.

• Check the battery terminals for dirt. Remove any dirt.

• The battery might be defective and have to be replaced.

Only use batteries of the same type.

The device does not start:

• The battery power might be too low. Recharge the battery.

• Check whether the battery is correctly connected to the

device.

Slide the battery onto the device in a way that the battery

terminals engage. The battery must lock in place in the

device.

• Check the battery terminals for dirt. Remove any dirt.

• The tacker guide nose is not properly pushed on the

workpiece. The trigger(2) is linked to the movable tacker

guide nose(5) and will only trigger if the tacker guide nose

is pushed on the workpiece.

Info

Wait for at least 10 minutes before switching the

device back on.

A wire nail or staple is jammed in the device:

Warning

Make sure that the battery has been removed from the

device!

Make sure not to hold the device by the trigger when a

staple or wire nail is jammed inside!

The trigger could be actuated by accident while

removing a jammed staple or wire nail.

• Open the magazine release and remove the wire nail or

staple.

No staple or wire nail coming out of the device:

• Check whether the wire nails have been inserted according

to the mark(20).

• Check the magazine filing level indication(3). If necessary,

insert new staples/ wire nails into the magazine.

Staple or wire nail does not penetrate deeply enough/

hardly penetrates the material:

• Check the impact force regulator and select a lower or

higher impact force stage, if required.

The device becomes hot:

• Keep the venting slots clear to prevent the motor from

overheating.

Info

Wait for at least 10 minutes before switching the

device back on.

The device still does not operate correctly after these

checks:

Please contact the customer service. If necessary, bring the

device to an authorised specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PTNS10-20V Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PTNS10-20V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info