Bedienungsanleitung Trotec PWLS 05-10 (Seite 7 von 10) (Englisch)

753924

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

EN 7

LED work lamp PWLS 05-10 / PWLS 06-10

1. Open the battery compartment(6) by removing the battery

compartment cover(5).

2. Insert the batteries with correct polarity into the battery

compartment(6) (+/-).

3. Close the battery compartment(6) by closing it with the

battery compartment cover(5).

ðThe device PWLS 05-10 is now ready to use.

Charging batteries for PWLS 06-10

Note

The battery can be damaged in case of improper

charging.

Pull out the USB charging cable(13) from the external

charger each time before switching the device on.

Never charge the battery at ambient temperatures

below -20°C or above 55°C.

Charge the battery of PWLS 06-10 completely before using the

device. Use the USB charging cable(13) and a standard

charger.

Proceed as follows to charge the battery:

1. Open the cover(10) of the USB connections at the back of

the cordless work light.

2. If applicable, plug the charger into the mains socket.

3. Put the USB charging cable(13) into the USB connection/

input(9) of the device PWLS 06-10 and into a charger.

ðWhen the battery status is very low, the charging time is

6-7hours.

ðWhen the battery is charged 25%, the first LED of the

battery indication(12) is illuminated in blue. When the

battery is charged 50%, the second LED of the battery

indication(12) is illuminated in blue. When the battery is

charged 75%, the third LED of the battery

indication(12) is illuminated in blue.

ðWhen the battery is charged 100%, the fourth LED of

the battery indication(12) is illuminated in blue.

4. When all LEDs of the battery indication(12) are illuminated

and the battery is completely charged, you can remove the

USB charging cable(13) from the charger and from the

device PWLS 06-10.

5. Pull the charger out of the mains socket.

ðThe LED work light and the charger may have become

warm during charging. Let the LED work light and the

charger cool down to room temperature.

ðThe device PWLS 06-10 is now ready to use.

Note

Note that the battery status of the device PWLS06-10

cannot be read while in operation. You can only read

the battery status while charging.

Operation

Tips and notes on handling the LED work light

General information:

• Avoid looking directly into the light source.

• Use the devices only for a temporary illumination of indoor

and outdoor areas, e.g. for construction sites.

• The devices PWLS 05-10 and PWLS 06-10 can be used as

strobe.

• The LED work lights are particularly suited for illuminating

larger areas.

Info

You can turn the handles of the LED work lights by

180° and set 6 positions.

Switching the device on and off

Switching the devices PWLS05-10 and PWLS06-10 on and off

works identically.

1. Press the on/off switch(3/7) 1x to switch the device on or

off.

ðOnce the device is switched on, the surface LED(1) is

illuminated.

ðOnce the device is switched off, the surface LED(1) is

not illuminated.

Setting brightness level and strobe mode

Setting brightness level and strobe mode works identically for

both devices PWLS 05-10 and PWLS 06-10

üCheck whether the batteries (standard or integrated) are

completely charged. If necessary, replace the batteries or

charge the integrated battery.

1. Set the lowest light intensity by pressing the on/off

switch(3/7)1x.

2. Set the high brightness level by pressing the on/off

switch(3/7)3x.

3. Set the strobe mode by pressing the on/off

switch(3/7)5x.

Always proceed in the same order to set the desired light

intensity or the strobe mode.

Note

By quickly pressing the

on/off switch(3/7), you can switch between the

brightness levels and the strobe mode.

Using the power bank

If you like to use the device PWLS 06-10 as power bank,

proceed as follows:

1. Put the USB charging cable(13) into the USB connection/

output(8) of the device PWLS06-10.

2. Then plug the USB charging cable into the USB input of the

device that you would like to charge.

3. Charge your device until it has reached the desired

charging status.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PWLS 05-10 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PWLS 05-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info