Bedienungsanleitung Trotec TAC 1500 (Seite 7 von 14) (Englisch)

580080

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

EN Operating Manual – Air Cleaner TAC 1500 / TAC 3000 6

• When putting up the device, position it in the room's centre

the air of which is to be cleaned. Alternatively, you can also

position the device near the source of air contamination.

• Prior to operation you have to ensure that the filters have

been installed in the device as desired.

• Also check, whether the pressure sensors are connected cor-

rectly. If the device, during operation, emits a warning of a fil-

ter being spent, the respective filter has to be replaced.

• Put the device up in a level, upright and stable position.

• Do not create tripping hazards when laying the power cable

or other electrical cables.

• Ensure that extension cords are completely unrolled.

Installation of the device in the room, the air of which is

to be purified

• The device works in recirculation mode, this means that the

contaminated air enters the air cleaner via the air inlet and is

blown out through the air outlet in purified state.

Fig. 8 Air purification in sealed off area via air circulation

Installation of the device outside of the room, the air of

which is to be purified

The device can be connected in either recirculation or ventilation

mode.

• In recirculation mode, the air to be cleaned is led via a hose

from the room into the air inlet of the device. The purified air

is fed through another hose from the air outlet and back into

the room.

• In ventilation mode, the air to be cleaned is led via a hose

from the room into the air inlet of the device. This creates a

slight negative pressure in the room. Clean, fresh air flows in

from outside.

Fig. 9 Installation variants for maintaining the pressure

When connecting pipes or hoses,

the following is to be observed:

• The used pipes and hoses must be designed for the available

static compression of the fans. They should preferably be laid

in a straight line and at full length. 7.6 m of air hose each can

be connected to both the TAC 1500's air inlet and outlet.

• To prevent an immediate neutralization of the air flows, air in-

let and air outlet should be positioned at a distance of at least

1 m from one another.

Control panel

Fig. 10 Control panel

Switch-on

• Switch the device on by actuating the mains switch (1). En-

sure that air inlet and outlet are not covered. The integrated

indicator light lights up.

Switch-off

• Switch the device off by actuating the mains switch (1). The

integrated indicator light goes off.

Operation

No. Designation

1 mains switch

2 fan speed controller

3 filter indication pre-filter (coarse particulate air filter G4

& fine particulate air filter F7)

4 filter indication high-efficiency particulate air filter

(HEPA H13)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec TAC 1500 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec TAC 1500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info