Bedienungsanleitung Trotec TGP1025ES (Seite 7 von 19) (Englisch)

756430

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

EN 7

garden pump TGP 1025 E / TGP 1025 ES / TGP 1025 ES ES

• Check whether there is residual water left in the device,

and drain any residual water via the water drain nozzle(5)

to prevent rust formation.

• Put the protective caps on the pressure and suction

connection to protect the inside of the device against dust

and dirt.

If you do not use the device for an extended period of time, it

must be cleaned thoroughly after its last application and before

recommissioning. Deposits and residues could lead to start-up

difficulties.

For restart, please proceed according to the Start-up chapter.

Assembly and installation

Scope of delivery

• 1x Garden pump

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power

cable is not damaged and that you do not damage it during

unwinding.

Start-up

Positioning

Warning of electrical voltage

Do not position the device in damp shafts. There is risk

of short circuit!

Note

Positioning the device in damp shafts can result in

damage to the device caused by corrosion!

Select a suitable location for positioning the device. It should

meet the following criteria:

• The site of installation is protected from weather exposure

and wet conditions.

• The surface is horizontal and level.

• The site of installation can support the weight of the device

and the pumped media.

For a permanent installation, the feet(8) of the device can be

bolted to the ground.

Connecting the pipe or hose line

The device may be operated using either a hose line or a pipe.

Ex factory, the device is delivered with a 1" internal thread.

Please note the following:

• The device cannot be moved flexibly when using a solid

pipe.

• Use a pressure line and suction line with a diameter

corresponding to the size of the connections or above. A

smaller diameter causes pressure loss and thus reduces

the feed rate.

• The smaller the delivery head of the pressure line and

suction line, the higher the flow rate.

• Connected accessories can cause a pressure loss and

reduce the feed rate.

Additionally, please note the following when connecting flexible

hose lines:

Note

If you want to connect a flexible hose as pressure line,

do not use a suction hose or a non-pressure-resistant

hose. Use pressure-resistant hoses only.

Note

If you want to connect a flexible hose as suction line,

use a vacuum-tight suction hose only.

Connecting the pressure line

Warning

Make sure that all parts of the pressure line are

installed professionally. In case of an improper

assembly or when using unsuitable parts, there is a

risk of injury due to the pressurized pumping medium.

1. Remove the protective cap(10) from the pressure

connection(2).

Note

Keep the protective cap of the pressure connection so

you can use it when storing the device to protect the

inside of the device against dust and dirt.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec TGP1025ES Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec TGP1025ES

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info