Bedienungsanleitung Trotec TGP1025ES (Seite 11 von 19) (Englisch)

756430

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

EN 11

garden pump TGP 1025 E / TGP 1025 ES / TGP 1025 ES ES

Errors and faults

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

Warning of electrical voltage

Tasks which require the housing to be opened

must only be carried out by authorised specialist

companies or by Trotec.

Warning

The device is pressurized. Before opening the screw

plug at the water filler neck(3) or water drain

nozzle(5), the pressure must be released from the

pressure line via the lowest-level consumer.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• Check the current pressure on the pressure gauge(9). Only

when the pressure is below the switch-on pressure of

1.5bar will the device switch on and operate until reaching

the switch-off pressure of 3bar.

• The device might have overheated and the thermal

protection circuit is activated.

If so, wait for approx. 10minutes before restarting the

device. If the device is not starting, have the electrics

checked by a specialist company or by Trotec.

• The water temperature is above 35°C and the thermal

protection circuit is activated.

The device is running, but not sucking in any water:

• Check whether the suction line is submerged in the

pumping medium and/or check whether the water level of

the pumping medium is sufficient.

• Check whether the screw plugs at the water filler neck(3)

and water drain nozzle(5) are completely closed and

whether the seal is installed correctly.

• Check the inside of the device for any remaining air. Open

the screw plug at the water filler neck(3) and fill the

device with water all the way to the edge.

• Check the suction line and the connection for tightness.

• Check whether the suction height is too high, and reduce it

if necessary.

• Check whether the hose line is kinked or blocked. Remove

kinks and/ or blockages.

Insufficient or decreasing conveying capacity:

• Check whether the suction height or pump height exceeds

the max. specifications indicated in the technical data, and

reduce it if necessary.

• Check whether the hose line is kinked or blocked. Remove

kinks and/ or blockages.

• Check whether the suction line is clogged at the intake

opening. Remove any dirt.

• Inspect both the pressure and suction line for leaks, and

replace them if necessary.

The pump switches on and off too often:

• Check whether the precharge pressure in the pressure

tank is set correctly; it should be 1.5 to 1.8bar. Please

refer to the chapter Checking the precharge pressure in

the pressure tank.

If the pressure tank cannot maintain the set precharge

pressure, the membrane inside the pressure tank is

damaged and must be replaced. If so, contact a specialist

company or Trotec.

• Check whether the check valve at the suction line is

blocked or damaged. Remove the obstruction or replace

the check valve.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

Notes on maintenance

Inside the device, there are no parts that need to be maintained

or lubricated by the user.

Note

If there is a danger of frost, drain all water from the

device via the water drain nozzle(5) to prevent the

device from being damaged. Before restart, the device

must be filled with water again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec TGP1025ES Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec TGP1025ES

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info