Bedienungsanleitung Trotec TP10 (Seite 7 von 12) (Englisch)

756407

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EN 7

pyrometer TP10

Operation

Inserting the battery

Note

Make sure that the surface of the device is dry and the

device is switched off.

1. Open the battery compartment by folding open the

cover(28) with your fingers.

2. Use the battery clip(27) to connect the new

battery(1x 9V) with correct polarity.

3. Insert the battery in the battery compartment.

4. Close the cover of the battery compartment(28).

Carrying out a measurement

• Ensure that the surface to be measured is free of dust, dirt

or similar substances.

• To be able to gain exact measurement results on surfaces

which reflect heavily, stick matt masking tape to the

surface or apply matt black paint with a very high and

known degree of emission.

• Note the 75:1 ratio of the distance to the measuring spot

diameter. For accurate measurements the measuring

object should be at least twice as large as the measuring

spot.

Please proceed as follows to carry out a measurement:

1. Point the device at the object to be measured.

2. Press the measurement button(7). Hold onto the

Measurement button(7) if you want to perform a

prolonged measurement.

ðThe device turns on and carries out a measurement.

ðThe SCAN symbol(12) appears in the display. The

currently measured value is indicated.

3. Let go of the Measurement button(7) again.

ðThe device stops measuring. The HOLD symbol(12)

appears in the display.

ðDepending on the setting of the device, either the

Max/Min value or the Avg/Dif value of the last

measurement will be displayed.

Settings

The bottom line of the display contains a three-part menu.

Within this menu different settings can be selected. You can

switch through the different menus using the Mode button(3).

Menu example:

MxMn Save Avg

The menu is controlled as follows:

• The F1 button(4) selects the function on the left, MxMn in

our example.

• The F2 button(5) selects the function in the centre, Save in

our example.

• The F3 button(2) selects the function on the right, Avg in

our example.

Setting the Max/Min function

1. Repeatedly press the Mode button(3) until the MxMn Save

Avg menu is displayed:

ðThe MxMn Save Avg menu is shown on the display.

2. Press the F1 button(4) to select MxMn.

ðThe maximum value is displayed in the upper

measurement value display(18).

ðThe minimum value is displayed in the lower

measurement value display(20).

ðThe discrepancy between the current measured value

and the minimum value is indicated as deflection on the

scale(21).

Setting the Avg/Dif function

Please bear in mind, that the average value is continually

determined anew during a measurement, which means that

there can be deviations of the displayed Dif value in the in the

hundredth °C range.

1. Repeatedly press the Mode button(3) until the MxMn Save

Avg menu is displayed.

2. Press the F3 button(2) to select Avg.

ðThe average value is displayed in the upper

measurement value display(18).

ðThe difference between the current measured value to

the average value is displayed in the lower

measurement value display(20).

ðThe difference between the current measured value to

the average value is indicated on the scale(21).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec TP10 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec TP10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info