Bedienungsanleitung Trotec TTP 10 E (Seite 8 von 12) (Englisch)

726482

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

8 EN

dehumidifier TTP 5 E / TTP 10 E

Switching the device on

Once you have completely installed the device as described in

the Start-up chapter, you can switch it on.

Warning of electrical voltage

Do not remove the condensation tank from the device

during operation.

The device keeps running even if the condensation

tank is not inserted!

Otherwise, water may drop from the device

uncontrollably and damage the device. There is a risk

of electric shock!

1. Press the on/off switch(1).

ð The indicator LED(10) is illuminated in green.

ð The fan switches on.

ð The device starts to dehumidify.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the condensation tank, if need be.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damage.

• Check the on-site fusing.

• Check the condensation tank for correct seating.

• Check whether the condensation tank is full. The indicator

LED(10) is illuminated in orange.

• Check the room temperature. Observe the device's

permissible ambient temperature according to the

technical data.

• Wait for 10minutes before restarting the device. If the

device is not starting, have the electrics checked by a

specialist company or by Trotec.

The device is running, but there is no formation of

condensate:

• Check the float in the condensation tank for dirt.

If necessary, clean the condensation tank. The float must

be able to move freely.

• Check the room temperature. Observe the device's

permissible ambient temperature according to the

technical data.

• Ensure that the relative room humidity complies with the

technical data.

• Check the air filter for dirt. If necessary, clean or replace

the air filter.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright

position.

Condensate is leaking:

• Check the device for leaks.

The device gets very warm, is loud or loses power:

• Check the air inlets and air filters for dirt. Remove external

dirt.

• From the outside, check the device for dirt (see chapter

Maintenance). If the inside of the device is dirty, have it

cleaned by a specialist company or by Trotec.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec TTP 10 E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec TTP 10 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info