Bedienungsanleitung Trotec TWP7506E (Seite 7 von 16) (Englisch)

756418

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN 7

submerged clear water pump, near-ground suction TWP 4006 E / TWP 7506 E

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

Before transporting the device, observe the following:

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Do not use the power cable to drag the device.

• Only carry the device by the transport handle.

• Do not carry the device by holding it at the power cable or

hose.

Storage

When the device is not being used, observe the following

storage conditions:

• Dry and protected from frost and heat

• In an upright position where it is protected from dust and

direct sunlight

• With a cover to protect it from invasive dust, if necessary

• Place no further devices or objects on top of the device to

prevent it from being damaged.

If you do not use the device for an extended period of time, it

must be cleaned thoroughly after its last application and before

recommissioning. Deposits and residues could lead to start-up

difficulties.

For restart, please proceed according to the Start-up chapter.

Assembly and installation

Scope of delivery

• 1x Submerged clear water pump

• 1x Reducer for hoses with inner diameters of 25mm or

38mm as well as hose connections withG1"/DN25

internal thread

• 1x elbow for hose connections with G1½"/ DN40 internal

thread

• 1x Backflow preventer (pre-installed)

• 1x Stainless steel washer (pre-installed)

• 1x Nylon cord (10m)

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power

cable is not damaged and that you do not damage it during

unwinding.

Start-up

Connecting the pipe or hose line

The device may be operated using either a hose line or a pipe.

Ex factory, the device is delivered with a connection for the

"Quick Connect" connection system.

Please observe the following information regarding water

discharge:

• Please note that making use of the reducer(7) might

decrease the device performance. The reducer should be

shortened to the used diameter so as not to affect the

device performance.

• Please note that the device cannot be moved as flexibly

when using a solid pipe.

• Note that the maximum particle size is reduced according

to the hose diameter.

• Please note that the conveying capacity declines with an

increasing length of the water discharge line.

Info

If required, you can cut the reducer(7) off at the

desired diameter.

At delivery the reducer(7) is already assembled with

the backflow preventer(8) and stainless steel

washer(9) onto the elbow(10).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec TWP7506E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec TWP7506E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info