Bedienungsanleitung Truma Elektroboiler (Seite 5 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

489381

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Installation instructions

Installation and repair are only to be carried out by an

expert. Always read and follow the operating instructions

carefully prior to starting any work!

The year when the equipment was first taken into oper-

ation must be indicated with a check on the type plate.

Choice of location and installation

Select installation site (not in installation compartment behind

heater) such that the hot water pipes are as short as possible.

The boiler must be easily accessible at all times for service

work and be easy to remove and install.

Securely screw boiler to suitable surface (plywood panel,

laminated wood strips, or metal base) on floor of vehicle with

B 5.5 x 70 screws and washers (1). Always use the support

sleeves (2) that are preinstalled in the factory to reinforce the

insulating jacket.

Water connection

All pressure and submergible pumps up to 2.8 bar are used

for operating the boiler and all mixed combination sets with or

without an electrical switch.

Fig. A

When using immersion pumps, a non-return valve (3 – not

included in the scope of supply) must be fitted between the

pump and the first branch point (arrow points in direction of

flow).

Fig. B

When using pressure pumps with high switching hysteresis,

hot water may flow back through the cold water tap. To pre-

vent the backflow, we recommend that a non-return valve

(4 – not included in the scope of supply) be fitted between the

outlet to the hot water tap and the drain valve.

Hoses with an inner diameter of 10 mm that are pressure-re-

sistant (up to 3.5 bar) and hot water-resistant must be used for

connecting to the boiler and the safety/drain valve.

For non-flexible pipe routing (e.g. John Guest System) Truma

can supply the water connections (5 + 6), the safety/drain

valve (7) and a non-return valve (3 + 4) with a 12 mm diameter

inner connection as accessories.

If connecting to a central water supply (rural or city connec-

tion) or when using more powerful pumps, a pressure reducer

must be used which prevents pressures of greater than 2.8 bar

occurring in the boiler.

Route the water hoses so that they are as short and

free of kinks as possible. All hose connections must be

secured using hose clamps (also for cold water)! Pressures

of up to 3.5 bar can occur in the safety/drain valve (also in

submergible pumps) because of the heat of the water and the

resulting expansion.

We recommend the use of hose clips (part no. 40712-01)

to fasten the hoses to walls or the floor. If gas heating

has been installed, the water hoses and the hose clips can be

laid on the hot air pipes, which prevents frost.

In order to guarantee that the boiler is completely emp-

ty, the enclosed elbow with breather valve (5) must be

used for the hot water connection!

All water pipes should be routed in a descending man-

ner to the safety/drain valve! There shall be no claims

under guarantee for damage caused by frost!

Elektroboiler (Electric boiler)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Elektroboiler Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Truma Elektroboiler

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info