Technical data
determined in accordance
with EN 814 or Truma test
conditions
Designation: Frostair 1700
Comfort air conditioner
Area of operation: Small
areas, mobile and stationary
Number of installation
units: 1
Dimensions (LxWxH):
555 x 405 x 285 mm
Weight: Approx. 26.3 kg
Power supply:
230 V - 240 V ~ 50 Hz
Maximum cooling capacity:
1.7 kW
Actual power
consumption:
0.65 kW
Start-up current:
15 A (150 ms)
Current consumption: 2.8 A
Protection mode: IP X5
Energy Efficiency Rate
(EER): 2.6
Sensitive heat factor:
1,96
Volume flow (cold air):
max. 260 m
3
/h
Cooling agent: R 407C
Cooling agent content:
See name plate on unit
Compressor oil:
Diamond MA32, 300 cm
3
Noise:
Depending on installation
situation
Maximum inclination of
vehicle during operation:
5° / 8%
Operational limits:
+ 16°C to + 40°C
- Below + 16°C an ambient
air sensor prevents the op-
eration of the compressor.
- An icing sensor prevents
impermissible formation of
ice on the evaporator.
- A temperature switch pre-
vents excess current flow
and excess temperature at
the compressor.
EEC Type Approval:
e1 022801
Right to effect technical
modifications is reserved!
Manufacturer’s
terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions in
the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
- Tor parts subject to wear
and in cases of natural
wear and tear,
- As a consequence of the
use of non-original Truma
components in the equip-
ment,
- As a consequence of failure
to respect Truma instruc-
tions for installation and
use,
- As a consequence of
improper handling,
- As a consequence of
improper transport pack-
ing, not arranged by Truma.
2. Scope of warranty
The warranty is valid for mal-
functions as stated under
item 1, which occur within
24 months after conclusion
of the purchase agreement
between the seller and the fi-
nal consumer. The manufac-
turers will make good such
defects by subsequent fulfil-
ment, i.e. at their discretion
either by repair or replace-
ment. In the event of manu-
facturers providing service
under warranty, the term of
the warranty shall not re-
commence anew with regard
to the repaired or replaced
parts; rather, the old warranty
period shall continue to run.
More extensive claims, in
particular claims for compen-
satory damages by pur-
chasers or third parties, shall
be excluded. This does not
affect the rules of the product
liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty - in particular
transportation costs, travel-
ling expenses, job and mater-
ial costs, as long as the ser-
vice is carried out in Ger-
many. The warranty does not
cover customer service work
in other countries.
Additional costs based on
complicated removal and in-
stallation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The manufacturer's address
is: Truma Gerätetechnik
GmbH & Co. KG, Wernher-
von-Braun Strasse 12,
D-85640 Putzbrunn. In Ger-
many, always notify the
Truma service centre if prob-
lems are encountered; in oth-
er countries the relevant ser-
vice partners should be con-
tacted (see list of addresses).
Any complaints are to be de-
scribed in detail. In addition,
the properly completed guar-
antee certificate is to be pre-
sented, or the factory number
of the unit and the date of
purchase given.
To avoid transport damage,
the device may only be dis-
patched after agreement with
the Truma Service Centre in
Germany or with the particu-
lar service partner concerned
abroad. The risk for possible
transport damage will other-
wise be borne by the con-
signor.
Dispatch is normally to be
carried out by freight for-
warders using the special dis-
patch boxes available from
Truma. If it is a case of war-
ranty, the factory shall bear
the cost for the delivery to
the factory and the cost for
returning the appliance to the
customer. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.
