Bedienungsanleitung Truma MonoControl CS Gastank (Seite 17 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

629586

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Truma Manufacturer’s Warranty

1. Warranty claims

The Manufacturer hereby warrants for all defects of the unit

caused by material or production faults. In addition, the seller

continues to be subject to any statutory warranty claims.

No warranty claim shall be applicable under the following

circumstances:

– Consumable parts which are subject to wear and tear

– Use of parts other than original Truma components in any

of the units

– Damage caused by foreign substances in the gas (e.g. oils,

plasticisers)

– Failure to observe Truma’s installation or operating instructions

– Improper handling

– Improper transport packing

2. Scope of warranty

The warranty covers all defects under clause 1 that occur

within 24 months upon concluding the purchase agreement

between the seller and the end customer. The Manufacturer

undertakes to remedy such defects through subsequent ful-

filment, i.e. at its discretion either by repairing or replacing

the defective item. If the Manufacturer remedies a defect

under its warranty commitment, the term of the Warranty

shall not recommence anew with regard to the repaired or

replaced parts; rather, the original warranty period shall con-

tinue to be applicable. No further-reaching claims shall be

permitted, especially damage claims presented by purchas-

ers or third parties. This provision shall not affect the validity

of the German Product Liability Act (Produkthaftungsgesetz).

The Manufacturer shall bear the cost of employing the Truma

Customer Service for the removal of warranty defects – in

particular, transportation, travelling, job and material costs –

provided that the Customer Service conducts its work within

Germany. This Warranty does not cover Customer Service

work outside Germany.

Additional costs arising from complicated removal or instal-

lation jobs on the unit (e.g. dismantling of furnishings or parts

of the vehicle body) are not covered by the Warranty.

3. Making a claim under the warranty

The Manufacturer’s address is:

Truma Gerätetechnik GmbH & Co. KG

Wernher-von-Braun-Straße 12,

85640 Putzbrunn, Germany

Should problems occur, please contact the Truma Service

Centre or one of our authorised service partners (see

www.truma.com). Please describe your claim in detail and

state the serial number of the unit and the date of purchase.

To help the Manufacturer determine whether your claim is

covered by the Warranty, the end user must take or send the

unit to the Manufacturer or service partner at their own risk.

If a unit is sent to the manufacturing facility, make sure it

is shipped as a freight item. If the claim is covered by the

Warranty, transport / shipping and the cost of return shall be

borne by the manufacturing facility. If the claim is not covered

by the Warranty, the Manufacturer shall notify the customer

to this effect, specifying the cost of repairs not borne by the

Manufacturer; shipping costs, too, shall be borne by the cus-

tomer in such a case.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma MonoControl CS Gastank Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info