Bedienungsanleitung Truma Mover Mover H SE R (Seite 14 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484650

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Remote handset

a = On / Off slide switch

❙ On (green LED illuminates)

£ Off (green LED goes off)

b = Caravan forwards (both wheels

rotate in forwards direction)

c = Caravan reverse (both wheels

rotate in reverse direction)

d = Caravan right forwards

(left wheel rotates in forwards

direction)

e = Caravan left forwards

(right wheel rotates in forwards

direction)

f = Caravan right reverse (left wheel

rotates in reverse direction)

g = Caravan left reverse (right wheel

rotates in reverse direction)

Mover® H SE R only

The caravan can be turned in a circle on the spot without

moving forward.

d + g = Turn caravan to the right

(left wheel rotates forwards + right wheel rotates

backwards)

e + f = Turn caravan to the left

(left wheel rotates backwards + right wheel rotates

forwards)

Mover® H TE R only

Turning on the spot without moving forward is not possible

because of the two axles. Pressing the d, g, e or f buttons

causes the Mover® to move in a circle, whereby the outer

motor runs continuously and the inner motor pulsates.

Mover® H SE R / H TE R

h = Two-hand operation, engage drive rollers

i = Two-hand operation, disengage drive rollers

To engage and / or disengage the drive rollers both keys

always need to be pressed at the same time for about 3 sec-

onds (safety lag) until the drive rollers start to engage or

disengage.

The keys can be released again when the drive rollers move

toward the direction of the respective final position. The drive

rollers reach their final position automatically.

Pressing the two buttons for disengaging whilst the

Mover® is engaging causes the procedure to be aborted.

The drive rollers will disengaged and automatically move to

the end position.

The remote hand set switches off:

after approx. 2 minutes, if no button is pressed

after approx. 7 minutes, if one of the movement buttons is

permanently held down. The green LED goes off.

To reactivate the remote control, move slide switch to “Off” £

and then back to “On”

❙ after approximately 1 second.

There is no “On / Off” switch on the caravan to be operated.

–

Operating instructions

General instructions

The Mover® H SE R was developed for overcoming inclines of

up to approx. 25 % with a gross weight of 1200 kg and 15 %

with a gross weight of 2000 kg,

and the Mover® H TE R for overcoming inclines of up to ap-

prox. 25 % with a gross weight of 1200 kg and 10 % with a

gross weight of 2250 kg on a suitable surface.

When manoeuvring with the Mover®s H TE R, set the height

of the nose wheel so that the towing bar sinks to a low point.

Depending on the weight of the caravan, the Mover® cannot

overcome obstructions that are more than about 3.0 cm in

height without assistance (please use wedges as a ramp).

Due to the nature of a radio signal, it can get corrupted by ex-

ternal terrain or objects. So there may be small areas around

the caravan where the quality of reception reduces, hence the

Mover® may stop momentarily.

When the Mover® is switched off using the remote

control the control unit remains in standby. In order to

switch off completely the battery must be disconnected or

an isolating switch installed.

Batteries

We recommend the use of so-called drive and lighting batteries.

Gel batteries and round cell batteries are also suitable.

These batteries are designed for high power demands and

have an extremely long service life. The maximum power con-

sumption of the Mover® on the steepest incline and carrying

the maximum weight is 150 A. The correct choice of battery

depends on the usage period and the scope of use (other

consumers in caravan). For Mover® operation we recommend

batteries with a capacity of approx. 80 Ah or more.

Example:

A fully charged lead-acid battery with a capacity of 80 Ah al-

lows the Mover® to be operated for approximately 30 minutes

with a full load (depending on weight of caravan, battery type

and terrain). On level terrain the Mover® has average power

consumption of approximately 35 A and therefore an operat-

ing time of approx. 2 hours.

The use of gel batteries or round cell batteries means that

smaller batteries can be used.

Batteries with more capacity allow the equipment to be used

for longer.

For optimum operation, we recommend the Truma

Mover® PowerSet.

Function description

Always observe the operating instructions and “Safety

instructions” prior to starting! The vehicle owner is respon-

sible for correct operation of the appliance.

Please note that the Mover® H SE R is only suitable

for single-axle towed vehicles and the Mover® H TE R

is only suitable for dual-axle towed vehicles from the

company Hobby.

The Mover® is a manoeuvring system with which a caravan

can be moved without the assistance of a towing vehicle.

It consists of two separate drive units, each of which has a

12 Volt DC motor. These units are mounted directly next to the

wheels on the vehicle frame.

Once the drive rollers have been engaged to the tyres using

the remote hand set, the Mover® is ready for operation. All op-

eration takes place using the remote hand set. This transmits

radio signals to the control unit. A separate 12 V lead-acid

battery or suitable lead-gel battery (not included in scope of

delivery) supplies the control unit with current.

Truma Mover Mover H SE R Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info