Bedienungsanleitung Truma Mover Mover H SE (Seite 19 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484673

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Functional dimension

To ensure that the Mover functions correctly, the clearance be-

tween the tyres and the swivelled driving rollers is 10 – 26 mm

(for loaded vehicles and loaded wheels).

If the clearance is

not within this range, steps must be taken to check whether

or not the correct tyre type is used (see “Identifying the angle

bracket”) or if the tyres are heavily worn. All tyres must have

the same inflation pressure as per the manufacturer’s instruc-

tions (check at regular intervals!).

10 – 26 mm

min. 110 mm

Driving direction

Fit covering plates

Place covering plate onto housing and fix in position with

3 guide pins in each case (knock in with a hammer or screw-

driver handle).

Installing the position indicator

Push the position indicator into the two holes in the gearbox.

Installation of motor cables and control unit

The Mover is only suitable for connection to 12 V batteries

(DC voltage)!

Remove battery cable terminals and disconnect any

external electrical power before starting work. If you are

unsure about the electrical installation, have it checked out by

a qualified Auto Electrician.

Two high-power cables for the drive motor (6 mm²) and a two-

wire cable for the swivel-in motor are pre-attached to each

motor. Mark the respective motor connecting cables (motor

A or B – see also wiring diagram) and temporarily route to the

intended control unit installation position on the underbody of

the caravan. An example of a suitable location for the control

unit is in a bed stowage box in close proximity to the manoeu-

vring system, at least 40 cm away from the battery.

Insert control unit into stowage box and secure with the sup-

plied chipboard screws (5 x 16).

Drill a 25 mm diameter hole on the floor of the caravan for

leading the cables through, approx. 150 mm from the control

unit terminal strip.

Take care to avoid any chassis members, gas pipes and

electrical wires!

Drill hole and lead cables through floor of caravan to control

unit in such a way that they cannot chafe (particularly when

leading through metal panels). This can be done using protec-

tive tubes, which will prevent the cables from being damaged.

The drive motors move during operation. To com-

pensate for this, the cables should be secured loosely

with a little play in this area in order to prevent cable stretching.

No cables must be routed over the control unit!

Secure cables to chassis and / or underbody using the sup-

plied clips and screws.

Seal hole in vehicle underbody using plastic body sealant.

Connecting diagram

(with conventional brake lights)

Top-down

view

Safety

socket

Pin 6

Pin 3

Swivel-in

motors

Drive

motor

Drive

motor

Battery

Installation

in front of

axle

Safety

contact

Fuse

1213

– + – +

+ –

– +

1234

Pin 6

Pin 3

+ –

Connecting the drive motors

Cut motor cable of drive motor that is furthest away from

control unit to length. Shorten the motor cable of the nearest

drive motor to the same length. The two drive motor cables

must be of the same length to ensure that the drive output of

the Mover is uniform! Excess cable must be routed in wavy

lines without looping.

Crimp the provided flat plugs onto the drive motor cables.

Release flap at control unit terminal strip by pressing and con-

nect cables as shown in wiring diagram (red = positive,

black = negative). Please ensure that the connections are

made properly!

Connecting the swivel-in motors

The positive connection (r) of the 2-wire motor connection

cables has been marked with a red longitudinal line along the

cable insulation.

Mark motor cables A + B and route to control unit (shorten

cables to same length if necessary).

Slide spade connector sleeve insulation over the cables

(e.g. black for motor A and transparent for motor B). Crimp on

spade connector sleeves, slide on spade connector sleeve

insulation and connect as shown in connecting diagram.

Connecting the battery

Route battery connecting cables (10 mm²) to control unit and

securely attach using the provided clips and screws.

The battery connecting cables must not be extended.

They must be routed separately from the motor cables,

and must not run over the control unit.

Route battery connecting cables so that they do not chafe

(particularly at leadthroughs through metal panels). Use suit-

able leadthrough grommets for protection in order to prevent

damage to cables. Connect battery connecting cables to the

existing battery terminals (red = positive, black = negative).

The connection to the control unit (as per the connecting dia-

gram) must take place in the order – nut, battery connection

ring, nut (torque 10 Nm ± 1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Mover Mover H SE Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info