Bedienungsanleitung Truma Mover XT (Seite 19 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

590214

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

LED 4 green flashes if radio connection has not yet been

established after switching on the remote

control

lights up when remote control is ready for op-

eration and the data link is stable

flashes in combination with acoustic signal

– 10 seconds after switching on the remote control if the con-

trol unit is not yet ready for operation

– if the control unit has been switched off

– after 1 minute without pressing a button on the remote

control

– after a radio communication interruption

All LEDs “off” and no audio signal

System off

(check batteries in remote control if necessary)

Remote control battery change

Please only use leak-proof micro-batteries with a steel outer

casing, type LR 03, AAA, AM 4, MN 2400 (1.5 V).

When inserting new batteries, take care not to reverse the

positive and negative terminals.

Figure 3

Empty, used batteries can leak and damage the remote

control! Remove the batteries if the remote control is

not being used for a long period of time.

No warranty is given for damage caused by leaking

batteries.

Before disposing of a defective remote control, always re-

move the batteries and dispose of them correctly.

Manoeuvring the caravan

Follow the “Safety instructions” before using the

Mover®XT / XT2.

Apply parking brake if caravan is uncoupled.

Disconnect 13-pin plug / adapter from vehicle and plug into

safety socket of caravan.

For safety reasons, the Mover®XT / XT2 can only be op-

erated if the 13-pin plug / adapter of the caravan is

plugged into the safety socket.

In the event of a malfunction, the 13-pin plug / adapter

must not be removed from the safety socket until the

parking brake has been applied, since removing the plug dis-

ables the electronic safety functions.

Switch on the remote control – green LED 4 flashes until the

control unit is ready for operation. If the control unit is not

ready for operation, the remote control switches off after

about 10 seconds.

Press the two buttons (i) for engaging simultaneously, and en-

gaging will start after approx. 3 seconds (safety delay).

Use the position indicator to check that both drive rollers

are correctly engaged.

Before starting the Mover®XT / XT2, release the parking

brake.

Movement in all directions is possible using the control knob

and the slide control.

The Softstart / Softstop makes the caravan start to move

without jolting, and brakes it gently when stopping.

When the control knob or slide control are released, or if the

radio signal is interrupted or becomes too weak, the caravan

stops moving. Radio equipment and other Mover® remote

controls will not activate your Mover®.

After start-up, the Mover®XT / XT2 moves at a steady speed

(according to the setting on the slide control). Speed increases

slightly on downhill slopes and decreases on uphill slopes.

After manoeuvring, apply the parking brake first and then

disengage the drive rollers from the tyres.

Move slide switch on remote control to the “Off” position

toswitch the remote control off (the Mover®XT / XT2 switch-

es to standby mode).

The slide switch also acts as an “Emergency Stop”

switch.

Remove the plug / adapter from the safety socket after ma-

noeuvring, otherwise the control unit will automatically switch

off after 1 hour. The battery is discharged with a quiescent

current of approx. 80mA if the plug / adapter is in the socket.

Coupling to a towing vehicle

The Mover®XT / XT2 allows a caravan to be coupled to a

towing vehicle without jolting and with millimetric precision.

However, this requires care and a degree of practice.

Following the operating instructions, move the caravan close

to the towing vehicle (apply parking brake and engage gear).

In order to position the caravan precisely, operate the control

knob or slide control until the caravan's coupling is located

precisely over the ball coupling on the towing vehicle. Then

couple the caravan to the vehicle by lowering it at the support

wheel in the usual manner.

Prepare the caravan for towing in the usual way.

The caravan must not be towed with the drive rollers

engaged.

Maintenance

Keep drive elements clear of coarse road dirt. When cleaning

the caravan, spray the Mover®XT / XT2 with a water hose to

remove mud etc. Make sure that no stones, twigs etc. are

trapped in it. The control unit does not require servicing. The

remote control must be kept in a dry place.

Clean the Mover®XT / XT2 as described above every year (or

before overwintering). Do not park the caravan with the drive

rollers engaged.

To prevent the battery from becoming totally discharged dur-

ing long periods of inactivity it must be disconnected and

recharged before using again. Charge the caravan battery

before starting up.

It is extremely easy for you or your caravan dealer to perform

the checking and maintenance of your Mover®XT / XT2 dur-

ing the annual inspection of your caravan. If in doubt, please

contact Truma Service or one of our authorised service part-

ners (see www.truma.com).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Mover XT Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info