Bedienungsanleitung Truma Mover XT (Seite 28 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

590214

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

If necessary, insert socket connector back into socket housing (i).

Screw socket housing (i) with rubber seal (h) to socket

holder (g) using 3 sheet metal screws (j). (Several positions

are possible by selecting the mounting holes on the socket

holder and rotating the rubber seal)

Lead cable loosely through the strain relief (k) and screw in

place with the 2 sheet metal screws. Depending on the instal-

lation situation, the cable can be led out of the socket holder

through one of the three recesses.

B 3.9 x 33

(3 x)

PT 4 x 10

Figure 36

Secure safety socket to the (plastic) shaft cover of the caravan

with 4 screws, nuts and washers.

M4 x 16

(4 x)

Washer 4.3

(4 x)

Nut M4 (4 x)

Figure 37

No holes must be drilled in the chassis.

Alternatively, the safety socket can be secured using the two

clips.

Figure 38

Route both wires to the control unit (shortening them if necess-

ary) and connect them to the connector block as shown in the

connecting diagram.

Re-check whether all cables are correctly connected, attached

using the provided clips and cannot chafe.

Function check

Check whether the battery is fully charged for operating the

Mover®XT / XT2.

Position the caravan on open, level ground and apply the

parking brake. The drive rollers must not be in contact with

the wheels and the corner jacks must be raised.

Connect the battery terminals to the battery. Check that all

cables are securely attached and not hot, and that there are

no signs of short circuits etc.

Plug the 13-pin plug / adapter into the safety socket.

Move slide switch on remote control to the “On” position.

This switches on the remote control, and green LED 4 flashes

until the control unit is ready for operation. If LED 4 does not

light up, check polarity and condition of batteries in remote

control.

Check that neither drive motor is running. With the remote

control switched on, operate the “slide control (C)”. Both drive

motors must rotate.

Engage drive rollers using remote control.

Ensure that there are no obstacles around the caravan and re-

lease the parking brake. Now check all functions several times

in accordance with the operating instructions.

Apply caravan parking brake. Disengage drive rollers and

move remote control slide switch to “Off” £ in order to switch

off the remote control and the Mover®XT / XT2. Re-check dis-

tance between drive rollers and tyres. Re-adjust if necessary.

The distance between the disengaged drive rollers and

the tyres is 20 mm.

Warnings

The installer or vehicle owner must apply the yellow sticker

with the warning information, which is enclosed with the ap-

pliance, in a location in the vehicle where it is clearly visible

to all users (e.g. the wardrobe door). Missing stickers can be

requested from Truma.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Mover XT Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info