Bedienungsanleitung Truma Mover XT2 (Seite 24 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

590215

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

10. Short mounting system

Replacement for standard mounting system if this cannot be

used due to lack of space and to compensate for the height

(30 or 60 mm) of substructures such as tanks.

Part. no. 60031-20000

Figure 18

11. Mud guard set (no illustration)

Replacement for the standard mud guards, if these cannot be

adapted to the Mover®.

Part. no. 60031-08200

In some cases installation is not possible because of the

design of the sub-frame. Contact your dealer if necessary.

Detailed installation instructions are included with each

mounting set.

The vehicle frame must not be drilled (unless using the low

chassis kit* and the Eriba Touring mounting set) or welded.

Wheel suspension parts must not be removed under any

circumstances.

* In the case of the AL-KO Vario III / AV chassis, the vehicle

frame must under no circumstances be drilled into even if

the low chassis kit is used.

Selecting a location

The Mover®XT should preferably be mounted in front of the

axle, but in exceptional circumstances (e.g. lack of space) it

is also possible to mount it behind the axle. The Mover®XT2

should preferably be installed behind the axle Only use the

bolts provided (or the mounting parts available as special ac-

cessories) to attach the Mover®XT / XT2.

Mud guards

When a Mover® is fitted, the existing mud guards must be

moved / adapted if necessary (max. distance between tyre /

mud guard 300 mm).

If the original mud guards cannot be used, the Truma mud

guard set (part no. 60031-08200) must be used and adapted.

The mud guards are installed behind the axle. No mud

guards are required in front of the axle.

max. 200 mm

Driving direction

Mover

max.

300 mm

Mover® XT, XT2

Figure 19

Adapting the mud guards to the Mover®

1. Remove the mud guards.

2. Fit Mover® in accordance with the following installation

instructions.

3. Determine dimensions a and b and transfer to mud guards.

The top leg of the fastening bracket must face towards the

rear of the caravan.

Determining the cut-out sizes

Mover® XT / XT2

ver

XT / X

Mover® XT, XT2

Figure 20

Cut out the template on the last page of the installation in-

structions, place it onto the mud guard, transfer the contours

and cut out.

Pay attention to left and right sides!

If necessary, make recesses in mud guard for apron contour

and attach mud guard to underside of caravan 300 mm from

tyre.

Fitting the drive elements

The frame of the vehicle must be free of rust, grease and

heavy soiling. There must be no damage in the area of the

wheel suspension.

The wheels and tyres fitted on the caravan must be of the

same size and type, and must be inflated in accordance with

manufacturer's instructions.

Remove all components from packing and place on the floor.

Figure 21

In order to guarantee the validity of the general oper-

ating permit (ABE), the type plates (f) must be present

on the cross-strut on the right and left.

Figure 22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Mover XT2 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info