Bedienungsanleitung Truma Saphir comfort RC (Seite 14 von 74) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

590218

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Safety instructions

Repairs may only be carried out by an expert!

To avoid transportation damage, the device may only be

dispatched if the Truma Service Centre in Germany or the

respective authorised service partner has been consulted

beforehand.

The power supply must be disconnected from the mains (all

poles) before opening the housing.

The 230 V, T 6.3 A H-type (slow, IEC 127) device fuse can be

found on the electronic control unit in the device, and must

always be replaced with an identical fuse.

The device fuses and connection cables must only be re-

placed by experts.

Guarantee claims, warranty claims and acceptance of liability

will be ruled out in the event of the following:

– Modifications to the device (including accessories)

– Failure to use original Truma parts as replacement parts and

accessories

– Failure to follow the installation and operating instructions

This may also invalidate the device operating permit, which in

many countries also denotes cancellation of the vehicle oper-

ating permit.

The refrigerant circuit contains R 407C refrigerant and must

only be opened in the factory.

The air outlet and and the circulated air intake must not be

obstructed under any circumstances. This is essential in order

to ensure that your device operates correctly.

The openings beneath the floor of the vehicle must be kept

free of dirt and slush. These openings must not be within the

range of the wheel spray – fit splash guard if necessary.

If underbody protection is being applied to the floor of the

vehicle, all openings beneath the vehicle must be covered so

that the spray mist that is created does not penetrate the de-

vice and cause malfunctions. Remove covers again when the

work is complete.

In order to avoid damage to the compressor, no uphill or

downhill slopes with an incline of more than 8 % must be

driven on when the device is being operated while driving

(e.g. with generator or voltage converter).

Do not operate the device for long periods with the vehicle at

an angle, since the condensation that is produced may not be

able to run away and may penetrate the vehicle under unfa-

vourable circumstances.

In order to ensure that the equipment works properly and to

avoid damage, only power supply sources with a purely sinu-

soidal waveform (e.g. voltage converter, generator) and with-

out voltage peaks must be used.

When the floor of the vehicle is being cleaned, it must be

ensured that no water penetrates the openings in the base

of the device when spraying with a high-pressure cleaner, for

example.

For safety reasons the device must always be closed during

operation, since this is the only way to ensure that no injuries

are caused by moving parts. Then strap around the electronic

housing must not be removed.

Notes on using air conditioning systems

– The Saphir comfort RC air conditioning system is designed for

minimal power consumption. You should still check whether

the camp site has adequate fuse protection (min. 6 A) before

starting the equipment up.

– Park the vehicle in the shade if possible.

– Darkening with shutters and / or a canopy reduces the

amount of heat radiation.

– Clean your roof at regular intervals (dirty roofs heat up more

than clean roofs).

– The vehicle must be properly ventilated before starting the

equipment in order to remove accumulated warm air from

the vehicle.

– When aprons or the like are being fitted, please ensure that

adequate openings are present for dissipating the supply

air. The opening for the warm outgoing air should not be at

the inlet side.

– In order to obtain a healthy room climate, the difference

between the inside and outside temperatures should not be

too great. The recirculated air is cleaned and dried during

operation. A pleasant room climate is produced by drying

the moist air, even if the temperature difference is minimal.

– Keep all doors and windows closed when in cooling mode.

– Full ventilation power can only be achieved at all three

openings if three cold air ducts are connected.

– The blow-out duct (part no. 40040-32500) must not be used.

– When in heating mode, only use “high” fan level for rapid

heating. Set to “medium” or “low” during continuous

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Saphir comfort RC Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info