Bedienungsanleitung Truma Saphir comfort (Seite 15 von 54) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

489375

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

The installation and repair of the appliance is only to be

carried out by an expert. Read the installation instructions

carefully prior to starting work and observe the instructions!

Figure A shows the minimum installation dimensions for

standard installation.

Figure B shows the side view with the electrical connections.

Figure C shows the standard installation of the Truma

Saphir comfort IR.

Purpose

This device was designed for installation inside mobile homes

and caravans. Any other applications are only possible after

consultation with Truma.

Approval

The air conditioner Truma Saphir comfort IR satisfies the basic

requirements of the EN 814, and the safety and environmental

stipulations of the EN 378.

Declaration of conformity

The device satisfies the requirements of the following EC

Directives:

EMC Directive 2004/108/EC

Low-Voltage Directive 2006/95/EC

Noise Suppression in Vehicles 2004/104/EC, 2005/83/EC,

2006/28/EC

Type approval number e1 03 4392

Pressurised Equipment Directive 97/23/EC

End-of-Life Vehicle Directive 2000/53/EC

Regulations

Guarantee claims, warranty claims and acceptance of liability

will be ruled out in the event of the following:

modifications to the unit (including accessories),

failure to use original Truma parts as replacement parts and

accessories,

failure to follow the installation and operating instructions.

Choice of location

The device is in principle to be installed in such a way that it is

readily accessible at all times for servicing work, and can be

easily removed and installed.

In order to achieve uniform cooling of the vehicle, the

air-conditioning unit must be installed centrally in a

stowage box or similar mounting in such a way that the air

distribution pipes can be laid vertically in covered areas.

The air-conditioning unit is mounted on the floor. The room air

which is to be cooled is drawn in directly by the device via an

additional air grille in the stowage box wall (1 – accessory, part

no. 40040-29200) or via other apertures with a total surface

area of at least 300 cm

The circulated air will be purified and dried while the

unit is in operation. Accordingly, if the unit is installed

in external stowage containers (e.g. double bottoms) suitable

steps must be taken to ensure that the air which is to be

cooled is extracted from the interior of the vehicle. The suction

intake of air from the outside can severely impair the effect of

the air-conditioning system.

If possible, position the unit so that the frame of the vehicle is

between the air inlet (LE) and the air outlet (LA).

–

Place the installation template into the stowage box that is

intended for installation and check the space situation for the

floor openings. The air conditioning unit should have at least

20 mm of clearance at the sides and 30 mm at the rear from

walls and any furniture items in order to prevent noise trans-

mission during operation. The minimum clearance at the front

is 200 mm, so that the fluff / particle filter can be changed.

The openings in the floor of the vehicle must be freely

accessible, and must not be blocked by frame sections

behind them or the like! The openings must not be within the

range of the wheel spray. Spray guards must be fitted if

necessary.

Installing the air conditioning system

when adequate space is available

Preparation

Fig. B

Remove installation materials and remote control from stow-

age compartments (a and b) of the unit.

1. Fig. C

Place installation template in stowage compartment and fix in

position. Mark mounting holes for the 2 front and rear retain-

ing brackets (2 – leg must be on the outside!).

2. Mark floor opening „LE” for the air supply, „LA” for the out-

going air and „KO” for the condensation drain.

3. Mark longitudinal edges of air conditioning unit to make the

unit easier to align.

4. Remove template and cut out the marked floor openings.

Before drilling, always check for underlying / concealed

cables, gas lines, frame sections and the like!

Then seal the edges of the openings in the floor of the vehicle

with underfloor protection.

5. Screw down each retaining bracket (2) using 3 screws.

6. Insert muff (11) for condensation drain (KO) from above.

7. Insert air conditioning unit in stowage compartment (be-

tween the two retaining brackets) and align using the marked

longitudinal edges.

When installing the unit, please ensure that the

muff (11) of the condensation drain is located in

the recess in the floor of the vehicle. Otherwise there is

a risk of water penetrating the interior! In order to pro-

vide good air circulation, the openings in the bottom of

the unit and the floor must align exactly. Correct opera-

tion of the unit cannot be guaranteed unless this is the

case!

8. The 4 side fastening brackets (3) that are held in place by

the two tension straps are screwed down using the provided

screws (2 screws per bracket).

The air conditioning unit must be attached at all sides

using the brackets provided in order to prevent unin-

tentional movement if vigorous movements occur (e.g. hard

braking).

9. Seal muff (11) for condensation drain all round from below

using body sealant.

10. Attach the two floor grilles (5) for „LE” and „LA” to the

floor of the vehicle from below with suitable screws or clips

(not provided).

Installation instructions

Truma Saphir comfort Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info