Bedienungsanleitung Trumatic Combi 6 (Seite 13 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484616

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Taking into operation

Heating operation is basically possible without

restriction with or without water content.

Check to make sure the cowl is unobstructed. Be sure to

remove any covers that may be present.

Turn on gas cylinder and open quick-acting valve in the gas

supply line.

Summer operation

(boiler operation only)

Move the rotary switch on the control panel to position

(c – summer operation) 40 °C or 60 °C. The green (b) and

yellow (g) LEDs light up.

After reaching the set water temperature (40 °C or 60 °C),

the burner will switch off and the yellow LED (g) will be

extinguished.

Winter operation

Heating with water temperature monitoring

Set the rotary switch to the operational setting “e”.

Set the rotary switch (a) to the desired thermostat setting

(1 – 5). The green LED (b) for operation is lit and simulta-

neously indicates the position of the selected room tem-

perature. The yellow LED (g) indicates the water‘s heat-up

phase.

The unit automatically selects the required power level ac-

cording to the temperature difference between the setting

on the control panel and the current room temperature.

Once the room temperature set on the control panel has

been reached, the burner switches back to the lowest stage,

and heats the water content to 60 °C. The yellow LED (g)

will be extinguished after the water temperature is reached.

Heating without water temperature monitoring

Set the rotary switch to the operational setting “d”.

Turn the rotary switch (a) to the desired thermostat setting

(1 – 5). The green LED (b) for operation is lit and simultane-

ously indicates the position of the selected room tempera-

ture. The yellow LED (g – water‘s heat-up phase) will be lit

only when the water temperature is below 5 °C!

The unit automatically selects the required power level ac-

cording to the temperature difference between the setting

on the control panel and the current room temperature. Af-

ter reaching the room temperature set on the control panel,

the burner will switch off. The warm-air fan will continue to

run at a low speed as long as the blow-out temperature

(on the unit) is higher than 40 °C.

If the boiler is filled, the water will automatically be heated

at the same time. The water temperature is then dependent

on the heating output being given off, and the duration of

heating required to reach the desired room temperature.

Heating with drained water system

Set the rotary switch to the operational setting “d”.

Turn the rotary switch (a) to the desired thermostat setting

(1 – 5). The green LED (b) for operation is lit and simultane-

ously indicates the position of the selected room temperature.

The yellow LED (g) will be lit only when the temperature of

the unit is below 5 °C!

–

The unit automatically selects the required power level ac-

cording to the temperature difference between the setting

on the control panel and the current room temperature. Af-

ter reaching the room temperature set on the control panel,

the burner will switch off. The warm-air fan will continue to

run at a low speed as long as the blow-out temperature

(on the unit) is higher than 40 °C.

Switching off

Use the rotary switch to switch off heater (position f). The

green LED (b) goes off.

If the green LED (b) blinks after switching off, then the

unit‘s after-running is active in order to reduce the unit‘s

temperature. This will end after a few minutes and the green

LED (b) will go off.

Always drain water contents if there is a risk of frost!

If the appliance is not to be used for a prolonged period, close

the quick-acting valve in the gas supply line and turn off the

gas cylinder.

Red LED “Failure”

The red LED (h) will be lit if there is a failure.

Please consult the Trouble-Shooting list for possible causes.

A reset (fault reset) is carried out by switching off, waiting

until all LED’s on the control panel have stopped flashing,

and then switching the heater on again.

If a window to which a window switch has been fitted is

opened, the heater stops operating and the red LED (h)

flashes. The heater continues operating when the window

is closed.

Filling the water heater

Check if the rotary switch for the drain valve (FrostControl) is

set to “Operation”, meaning that it is parallel to the water

connection and engaged.

Close the drain valve by pushing the push button until it

engages.

When the temperature at FrostControl is below about

7 °C, first switch on the heater to warm the installation

compartment and FrostControl. After several minutes, when

the temperature at FrostControl is above 7 °C, the drain valve

can be closed.

Switch on power for water pump (main switch or pump switch).

Open hot water taps in kitchen and bathroom, (set preselect-

ing mixing taps or single-lever fittings to “hot”). Leave the fit-

tings open for as long as it takes for the boiler to displace the

air and fill up, and the water to flow without interruption.

If just the cold water system is being operated, without

using the water heater, the heater tank also fills up with

water. To avoid frost damage, the boiler must be drained

through the drain valve, even if it was not operated.

When connecting to a central water supply (rural or city

mains), a pressure reduction valve must always be in-

stalled to prevent pressures above 2.8 bar from developing in

the water heater.

Trumatic Combi 6 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info