Bedienungsanleitung Trumatic E 2400 (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484023

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Double cowl duct connection to the

heating appliance

Press end of ex haust duct (1) together so that winding touch-

es winding. Slide clamp (4) over exhaust duct (1). Slide ex-

haust duct over O-ring on the connection fitting (2) up to the

collar (3). Attach with clamp (4) in such a way that the knurled

edge of the clamp encloses the collar. Fasten combustion air

supply duct (5) on the connection fitting (6) using clamp (7).

Always install a new O-ring following any disassembly!

Under-floor assembly with wall cowl kit

Refer to installation variant fig. 2 (page 2).

Install wall cowl on as flat a surface as possible on an outside

wall (vehicle apron, refer to “Notes on installation in driver's

cab”).

If the wall cowl is fitted with fixing brackets or similar

below the floor, the vehicle floor must be airtight and

the waste gas must always be guided up to the side wall (see

„Choosing the installation place“).

Fastening the appliance

Screw the 3 fastening strips (1, 2 + 3) to the appliance. Screw

appliance to vehicle floor with the strips 1 + 2. Fasten assem-

bly bracket (4 – Accessories part. no. 39050-74000) together

with strip (3) and screws (5). Place lock washers under all

screw heads and nuts.

Warm air distribution and circulating air

return with interior installation

Warm air distribution

Hot air suction apertures must be arranged in such a way that

no exhaust gases from the engine or the heating device can

be drawn in. It must be ensured by means of construction

design that the heating air introduced into the vehicle is not

polluted (e.g. by oil vapour). This is achieved, for example,

with air heaters with circulating air operation, both for interior

installations and for external installations (in heaters with fresh

air operation the fresh air is not to come from the engine com-

partment or from the vicinity of the exhaust or the exhaust

outlet of the heater).

The warm air (W) is blown out from the appliance, either

directly or using a warm air duct VR 80 (80 mm diameter).

Remove grating from warm air outlet of the appliance. Con-

nect duct VR 80 (80 mm diameter). By positioning a manifold

section, the ducts VR 72 (72 mm diameter), ÜR (65 mm diam-

eter) or ZR 18 (49 mm diameter) can also be added on.

In order to avoid overheating, there must be at least one

air passage which is always open (swivel nozzle SCW 2).

Secure all duct connections with self-tapping screws. Fasten

ducts with clamps.

The hot air system is individually designed for each vehicle

model using a modular principle. A wide range of accessories

is available for this purpose (see brochure). Diagrams with op-

timum installation suggestions for hot air systems in all of the

most popular motor home models can be requested free of

charge via the Truma service centre.

Circulating air return

The circulating air (U) is sucked back into the appliance, either

directly or via a duct piece VR 80 (80 mm diameter).

1. Direct intake: If the appliance is installed in a storage com-

partment or such, drill two holes measuring 75 mm in

diameter into it, or make a corresponding opening for the

circulating air return.

Do not obstruct the air passage to the appliance!

2. Circulating air outside the storage area can be drawn in

via a duct piece VR 80 (1) 80 mm diameter (max. 1 m in

length) and returned to the appliance. The storage compart-

ment can then be used to the full.

Remove protective grating from the connection fitting (3).

Insert duct piece (1) into the grating connection fitting and

fasten using the available screws. Attach swivel nozzle SCW 2

to the duct end (4).

min 0.5m

max 1m

Warm air supply and circulating air return

with outside assembly

Refer to installation variant fig. 2 (page 2).

The warm air supply and the circulating air return between

appliance and vehicle is provided by means of flexible air

ducts LF 18 (83 mm diameter, 60 cm in length). The air ducts

can be shortened as required. A protective casing over the

entire heater system protects it against damage and weather

conditions and simultaneously serves as insulation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic E 2400 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info