Bedienungsanleitung Trumatic Handdoekdroger (Seite 7 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484605

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Attachment

The towel dryer is attached to a level wall in two locations. The

catches are clipped into the end outlet at the bottom. The cap

on top provides stability together with a mounting plate that is

screwed to the wall beforehand.

Before attaching to the wall, check wall thickness

(at least 8 mm) and composition (concealed cables,

gas lines, frame parts or the like)!

Installation

Assemble towel dryer as shown in diagram (see illustration on

page 5).

Fig. A: Clip assembled towel dryer into warm air vent (bot-

tom attachment point).

Then clean wall attachment point (top attachment point)

using alcohol or similar.

Remove protective film of adhesive strip from fitted cap.

Align towel dryer vertically using a spirit level and push firmly

against the wall.

Fig. B: Remove cap and secure mounting plate that is now

stuck to wall with 2 screws (provided).

Slide cap back onto towel dryer bar and over the attached

mounting plate. Towel dryer is now ready for use.

Affix provided sticker “Heat warning” to towel dryer bar

or in vicinity of towel dryer.

Manufacturer’s terms of warranty

1. Case of warranty

The manufacturer grants a warranty for malfunctions in the

appliance which are based on material or production faults.

In addition to this, the statutory warranty claims against the

seller remain valid.

A claim under warranty shall not pertain:

– for parts subject to wear and in cases of natural wear and

tear,

– as a result of using parts that are not original Truma parts in

the units,

– as a consequence of failure to respect Truma instructions

for installation and use,

– as a consequence of improper handling,

– as a consequence of improper transport packing, not

arranged by Truma.

2. Scope of warranty

The warranty is valid for malfunctions as stated under item

1, which occur within 24 months after conclusion of the

purchase agreement between the seller and the final con-

sumer. The manufacturers will make good such defects by

subsequent fulfilment, i.e. at their discretion either by repair

or replacement. In the event of manufacturers providing

service under warranty, the term of the warranty shall not

re commence anew with regard to the repaired or replaced

parts; rather, the old warranty period shall continue to run.

More extensive claims, in particular claims for compensatory

damages by purchasers or third parties, shall be excluded.

This does not affect the rules of the product liability law.

The manufacturer shall bear the cost of employing the Truma

customer service for the removal of a malfunction under war-

ranty – in particular transportation costs, travelling expenses,

job and material costs, as long as the service is carried out in

Germany. The warranty does not cover customer service work

in other countries.

Additional costs based on complicated removal and installa-

tion conditions of the appliance (e.g. removal of furniture or

parts of the vehicle body) do not come under warranty.

3. Raising the case of warranty

The manufacturer's address is:

Truma Gerätetechnik GmbH & Co. KG,

Wernher-von-Braun Strasse 12,

85640 Putzbrunn.

In Germany, always notify the Truma Service Centre if prob-

lems are encountered; in other countries the relevant service

partners should be contacted (see Truma Service Booklet or

www.truma.com).

Any complaints are to be described in de-

tail. In addition, the properly completed guarantee certificate

is to be presented, or the factory number of the unit and the

date of purchase given.

In order for the manufacturers to be able to determine wheth-

er an incident subject to guarantee has occurred, the end user

must, at his own risk, bring the device to the manufacturers or

send it to them.

In instances of the device being sent to the works, dispatch is

to be effected by freight transport. In cases under guarantee,

the works shall bear the transport costs or the costs of deliv-

ery and return. If the damage is deemed not to be a warranty

case, the manufacturer shall notify the customer and shall

specify repair costs which shall not be borne by the manufac-

turer; in this case, the customer shall also bear the shipping

costs.

dhesive

strip

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic Handdoekdroger Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info