Bedienungsanleitung Trumatic Ultraheat (Seite 6 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

484606

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Push sealing plate (8) about 3 cm onto the exhaust duct (claw

must point to the sleeve on the heater). Insert thrust collar (17).

Replace O-ring (16) with the enclosed O-ring.

The enclosed 53 x 5 mm O-Ring may only be

used with heaters from model 01/88 onwards.

The 35 x 5 mm O-ring (part no. 10030-25000) must

be used for older heaters. In this case consult your

specialist dealer!

Stretch O-ring (16) and carefully insert over the cut end of

the duct and push the exhaust duct in t o the sleeve as far as it

will go.

Push the O-ring, the thrust collar and the sealing plate up to

the sleeve. Attach sealing plate (8) by turning and tighten with

screw (9).

Fig. B

Screw gas supply line (7) back on beneath the vehicle.

Affix the enclosed nameplate to the inside of the heater cover.

Reattach heating cover.

Installation of the control panel

When using operating elements which are specific to

the vehicle or the manufacturer, the electrical connec-

tion must be established in accordance with the Truma inter-

face descriptions. Any modification made to the Truma com-

ponents pertaining to this will lead to the invalidation of the

guarantee, as well as to the exclusion of any claims for liability.

The installer (manufacturer) is responsible for providing in-

structions for use for the user as well as for identification

printing on the control panels!

In selecting a location, make sure that neither the front nor the

back of the control panel will be exposed to direct heat.

Length of connection cable 3 m. If required, a cable extension

of 5 m in length is available (which in combination can be

extended to 8 m – part no. 34300-01).

If the control panel can only be installed behind curtains or

similar location where temperature fluctuations may occur, it

is necessary to use a remote sensor for the room temperature

(part no. 34201-01).

If the control panels cannot be flush-mounted, Truma

can provide an on-surface frame (18), part no. 40000-

52600, as an accessory.

Fig. G

Drill a hole 55 mm in diameter.

Plug the operating cable (19) into the control panel (20) and fit

on the rear cover cap (21) as a strain-relieving device.

Feed the cable through to the back, secure the control panel

with four screws (22) and fit the cover frame (23).

Truma offers side parts (24) in eight different colors for

finishing the cover frames in a visually pleasing way.

Please ask your dealer.

Route the control panel cable (19) to the appliance and

connect to the control electronics.

For strain relief, secure control panel cable (19) on the control

electronics by means of enclosed cleat (25).

Depending on the method of installation, the control

panel cable may be installed in the reverse direction, i.e.

connected first to the control electronics and secured by

means of the cleat. Then feed through to the control panel

and connect it to the latter.

230 V Electrical supply

The 230 V electrical connection must always be made

by an expert (in accordance with VDE 0100, part 721 or

IEC 60364-7-721, for example, in Germany). The instructions

provided here should not be understood as a recommendation

for amateurs to install the electrical supply line. They are in-

tended as additional information for the professional electri-

cian you have hired!

Connect to the mains supply via the 150 cm long silicone

cable by means of a fuse-protected line of at least 10 A (better

16 A).

Be sure to connect the wires according to the correct colours!

For maintenance and repair work a separator must be provid-

ed for all-pole separa-tion from the mains supply with at least

3.5 mm contact clearance.

Function test

Before operating for the first time, the appliance, ex-

haust ducting and gas-tightness of the whole installa-

tion (by the pressure drop method) must be checked by

an expert.

In order to avoid damage to the electronics, make sure that

the hot air hoses on the Trumavent fan are attached securely

and fastened with a screw.

Finally, test all functions of the appliance in accordance with

the operating instructions.

The operating instructions must be handed to the owner of

the vehicle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic Ultraheat Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trumatic Ultraheat

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info