Bedienungsanleitung TTulpe C-Meister 14 P37 Eco (Seite 20 von 24) (Englisch)

782478

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

To calibrate the gas valve (standard procedure MANU: it is possible to

deviate from the value set by approximately +/-1.5 mbar) carry out the

following operations:

hPlace the electric switch of the system to off

hRemove the casing by unscrewing the fastening screws located at the

bottom of the water heater and detached the casing from the top

hRemove the cover that closes the service inlet (located on the

shelf - Fig 11) and insert through the hole the silicon pressure

gauge tube

hLoosen by approximately two turns the screw of the pressure tap

downstream of the gas valve and connect the pressure gauge to it

hCarefully close the casing and place the electric switch of the sys-

tem to on

hAccess the Calibration Menu

hOpen the hot water tap and wait until ignition of the burner.

Upon activation of the menu will appear rst the word Ma and then the

word to to compose Manu and will appear, indicating that the

water heater is operating at maximum capacity.

hTurn the knob until visualize on the pressure gauge the maximum

burner pressure (see data table)

hTo store the value press the reset button

hPress the reset button to select the next lowest setting value

hTurn the knob until visualize on the pressure gauge the minimum

burner pressure (see data table)

hTo store the value press the reset button

hPress the reset button until MENU’ ashing, release the button:

the display shows

hPress again the reset button until the display shows MENU’ ashing,

release the button: the display shows the set point temperature

hClose the hot water tap.

The calibration operation ends automatically after 15 minutes of

inactivity or in the case of overheating (67°C)

Alarm history menu

This feature allows displaying of the last 10 errors that have occurred on

the appliance.

Upon activation of the menu, the gures (index of the last stored

error), the error code and the word (es: => => ) will

appear alternately.

Turning the knob it is possible to scroll through the errors index. Display

ranges from the most recent to the earliest.

If the user pauses, the display shows the letters AL to indicate access

within the errors history menu.

Press the reset button until MENU’ ashing, release the button: the di-

splay shows .

Press again the reset button until the display shows MENU’

ashing, release the button: the display shows the set point tem-

perature.

Info menu

This feature allows displaying:

hLast version of software review

hHot water temperature in direct

hHot water quantity in direct (l/min).

This menu is active during all the production of instant hot water.

Exiting the menu takes place automatically after 15 minutes of

inactivity or by pressing the reset button.

Fig. 25 - “Alarm History Menu” Activation

Fig. 24 - “Calibration Menu” Activation

Fig. 26 - “Info Menu” Activation

Eco

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TTulpe C-Meister 14 P37 Eco Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TTulpe C-Meister 14 P37 Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info