Bedienungsanleitung TTulpe Indoor B-11 P50 Eco (Seite 8 von 12) (Englisch)

782452

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

the device;

- check that the device receives the type of gas it is manufactured

to process;

- check that the gas supply pressure does not go beyond the ma-

ximum pressure values displayed on the information plate;

- check that the gas supply system supplies the necessary amount

of gas to the device and that it is equipped with all the necessary

safety devices prescribed by current regulations.

If the user is absent for a lengthy period, turn off the main gas

supply tap.

Do not obstruct the area’s ventilation openings where the device is

installed to avoid dangers such as the build up of toxic and explosi-

ve substances. Do not utilize gas tubes to earth electrical devices.

Water connection

Connect the water heater to the water supply and insert a tap to in-

tercept the water above the device. From the front, the cold water

input is on the right and the hot water output is on the left.

Insert the lter into the water valve input tting.

Remove the plastic nut from the hot water output ttin before

connecting it to the water supply.

Check the water hardness (°f).

In case of high water hardness we recommend to install

upstream of the appliance the water softener device or other

device in compliance with the regulations including any revi-

sions.

Ensure that the tubes of you water system are not used to earth

your electrical system or telephone, they are absolutely inappro-

priate for performing this task.

In a short amount of time this can damage tubes and the device.

Disposal of waste product

This B11BS water heater is supplied with a device for releasing

ue gas.

For output of combustion by-products refer to the regulations in

force including any updates.

The gas devices with an attachment for a waste gas ue must be

connected directly to properly working chimney or ue pipe; only if

these devices are not present is it then permitted to release gases

directly outside.

The tting of devices to a chimney or ue pipe must occur via a

1 Release hood

2 Flue gas safety device

3 Water limit thermostat

4 Heat exchanger

5 Burner

6 Sensor electrode

7 Pilot burner

8 Ignition electrode

9 Injector

10 Hot water output

11 Pressure intake

12 Temperature selector

13 Venturi

14 Hydraulic valve

15 Flow regulation gas screw

16 Water lter

17 Membrane

18 Cold water input

19 Economiser

20 Gas valve

21 Safety device

22 Gas lter

23 Battery

24 Electrical card

25 Microswitch

Fig. 5

smoke channel. Smoke channels must be connected to a chim-

ney or a smoke channel in the same or adjacent area to where

the device is installed and must be made of materials resistant to

mechanical strain, heat and the effects of combustion by-products

and their condensation. The ue gas temperature must always be

above condensation temperature in all points of the smoke channel

regardless of external conditions.

FLUE GAS RELEASE SAFETY DEVICE

The product is equipped with a series of ue gas release safety

devices. The device ensures the correct release of combustion by-

products; the ow of combustible gas to the release conduit and

the smoke channel.

The safety device contains a “thermostat”, it can stop the ow of

gas to the main burner and the pilot ame.

The safety device can be triggered by the partial or total obstruction

of the release conduit or the smoke channel.

To reset the device it is necessary to press the ue gas ther-

mostat key (Fig. 6) close use a screwdriver and reopening the

hot water tap.

If the device or its electrical connections breaks down, the product

can not be put ON, it ensures a safe condition

If the device or its electrical connections breaks down, the machine

operation is blocked.

If the machine is constantly blocked as a result of the ue gas sa-

fety device, it is necessary to request the assistance of a qualied

technician accor-

ding to law in force,

to check the correct

release of ue gas

through the release

conduit and/or the

smoke channel, ac-

cording to the instal-

lation regulation.

It is highly prohibited

to attempt to modify

or remove the ue

gas safety device;

this risks the safety of

the user and persons in the area. Only a qualied technician who is

authorised by the manufacturer can meddle with the safety device

in order to check it’s functionality or to substitute it if necessary.

If it is necessary to replace the device it is vital to only use “original

parts” supplied by the manufacturer

since it has been designed, studied

and regulated to be tted with the wa-

ter heater.

g. 6

1 Cappa scarico

2 Dispositivo di controllo fumi

3 Termostato limite acqua

4 Scambiatore di calore

5 Bruciatore

6 Elettrodo di rilevazione

7 Bruciatore pilota

8 Elettrodo di accensione

9 Iniettore

10 Uscita acqua calda

11 Presa di pressione

12 Selettore di temperatura

13 Venturi

14 Valvola idraulica

16 Filtro dell’acqua

17 Membrana

18 Entrata acqua fredda

19 Economizzatore

20 Valvola gas

21 Dispositivo di controllo

22 Filtro gas

23 Batteria

24 Scheda elettronica

25 Microinterruttore

15 Vite di regolazione portata gas

Water Water

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TTulpe Indoor B-11 P50 Eco Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TTulpe Indoor B-11 P50 Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info