Bedienungsanleitung TTulpe Indoor B-14 P37 Eco (Seite 7 von 12) (Englisch)

782453

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

INSTALLATION

Regulations

The use of gas devices is controlled by precise regulations.

It is essential to observe all the regulations in force.

Installation of liquid petroleum gas (L.P.G) must comply with all the

distributor’s requirements and those of the regulations.

Wall mounting

Warning

Do not install this device in an area that contains dust, greasy va-

pour and/or corrosive elements.

- The device must be installed on a suitable wall surface in proxi-

mity to a fume disposal ue

- It is vital to leave the minimal distances around the device as

shown in g 3 to allow for maintenance operations to take place.

Location

The water heater must not be tightly placed in an enclosure or slot,

it should have an adequate ow of air around it

- The water heater must not be placed above a kitchen or other

cooking devices that might deposit grease vapour on its exterior

leading to corrosion

- Surfaces that sensitive to heat (e.g. wood) must be protected

using appropriate insulation.

- Fig. 1 displays the dimensions necessary for wall mounting

Room ventilation

The installation of the water heater must comply with regulations in

force including any updates.

Warning: This device can only be installed in venues that are per-

manently ventilated according to regulation in force.

Air circulation

It is vital that areas where gas devices are installed (type B) have

access to the amount of air necessary for the regular combustion of

gas as well as the ventilation of the venue.

- It is prohibited to use an extractor fan, replaces and other similar

devices at the same time as the water heater

- The area where the water heater is installed must have a regular

ow of air for ventilation.

Air ow

The ow of air must occur by the following means:

- Permanent openings in the wall that lead outdoors

- Single or collective ventilation ducts.

The air used for ventilation must be taken directly from an outside

location, that is far from sources of pollution.

Indirect ventilation from adjacent areas are permitted with the fol-

lowing limitations:

- The adjacent area is equipped with direct ventilation

- The devices within the area to ventilate are connected to a waste

duct

- The adjacent area does not contain a bedroom and is not a com-

mon area;

- The adjacent area is not a re hazard such as a storage area for

ammable materials, garage etc.

- The adjacent area is not lower than the area to ventilate as this

might lead to an opposing draught (this can be caused by other

devices that operate on the basis of combustion, a replace or

any suction device that have not been given an adequate air

supply)

- The air ow from the adjacent area occurs freely through perma-

nent openings.

Electrical connection to battery

The device is powered by a 1.5 V battery, alkaline long lasting mo-

del LR20, thus it is not necessary to connect the device to a power

socket.

Fig. 3

CARD CONNECTION

GN3 Earth

SV2 Burner solenoid valve

SV1 Pilot solenoid valve

SW Micro water contact

NC Not utilized

V+ Positive feed

GN2 Negative feed

GN1 Micro water contact

T.L. Water limit thermostat

T.F. Flue gas thermostat

M.S. Micro water

B Battery box Fig. 4

Gas connection

Determine the pipe diameter according to current regulations.

Before installing the device blow in the gas pipe to eliminate any

residue from its manufacturing. Connect the water heater to the

internal system’s gas pipes and place a tap above the device for

the halting and release of gas.

The main gas supply pipe must be connected by a at seat ttings

that allows the insertion of a gasket specically provided for gas

connections.

Do not use a conical seat ttings or union conical with threading

sealed with hydraulic hackled hemp or teon.

The water heaters that are powered by tanks of L.P.G. gas with

regulation and interception devices, must be connected correctly

so to guarantee the safety of persons and the surrounding area.

Follow all related regulations.

When initially installing the device qualied persons must perform

the following tests:

- Check that the internal and external parts of the gas supplying

device are sealed;

- check that the gas quantity supplied is equal to that required by

nero black

verde green

arancione orange

marrone brown

rosso red

50 50

200

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TTulpe Indoor B-14 P37 Eco Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TTulpe Indoor B-14 P37 Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info