Bedienungsanleitung TTulpe Smart Master DU080 (Seite 12 von 52) (Deutsch, Englisch, Holländisch, Französisch)

782608

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

SETTINGS AND MENUS - FIG. 6

The Setting mode is entered by pressing

(II) button, which visualizes the main menu (1). Scrolling in the menu is

performed by ▲ and ▼ buttons. To enter the current setting press (VIII)

button. After the screen with relevant setting is displayed, individual

parameters contained therein are adjusted as follows:

џThe current parameter is displayed enclosed in a blue rectangle (2).

Parameters are toggled with ▲ and ▼ or ◄ and ► buttons.

џPressing (VIII) button enters a current parameter adjustment mode

(3), whereby its value is displayed in a red rectangular. In this mode,

▲ and ▼ buttons may change the parameter value.

џAfter the required value is selected press (VIII) button to confirm the

change and exit the parameter adjustment mode.

џParameters in the form of ticks (4) can be changed by pressing (VIII)

button, which directly changes the tick status (enabled/disabled).

After all parameters are set, changes are confirmed by pressing (VII) button,

whereby the controller returns to the main menu containing the following

settings:

џTime and date (5) – sets date and time of the controller. Moreover, it

controls the automatic synchronization function where a WiFi module

is available.

џLanguage (6) – sets the language in which all messages are

displayed on the screen of the controller.

џDisplay (7) – changes display brightness and dims by reducing the

brightness, 30 seconds after the last time a button is pressed.

џTimer1-7 (8) – adjusts the week program timer operation. For each

timer it is necessary to enter the beginning and end of the interval, to

specify in which week days to operate and the maximum heating

temperature of the water when the current moment is within the

interval.

ATTENTION! In order to use a timer it must be activated! When entering

a beginning and end of the interval, it must be taken into account that the

thermoregulator will not allow for the end to precede the beginning!

џStart time of “day” and “night” tariffs (9) – sets the start time of both

tariffs, for which the controller maintains energy meters.

ATTENTION! To enable correct functioning of Smart Control mode, the

start times of both tariffs must be entered properly!

џSystem settings (10) – sets a mode, mounting position of the water

heater (horizontal or vertical), heater power, water heater capacity,

activation of the Anti-Legionella function and concurrent operation of

both heating elements (Fast Heating). Upon selection of the

‘Horizontal’ field, after exiting the menu, the screen will rotate

horizontally with right-side buttons. If the ‘Fast Heating’ field is

selected, the concurrent operation of both heating elements will be

permitted. If that field is not selected and there are conditions to switch

on the two heating elements, the element of the outlet water tank will

switch on first and after it switches off the heating element of the inlet

tank.

ATTENTION! For the proper metering of energy consumed and correct

functioning of Smart Control mode, it is essential that the heating

element power and water tank volume are properly set.

џSmart Control (11) – fine adjustment of control algorithms for Smart

Control mode. The ‘Priority’ field sets the energy saving method:

priority use of the cheaper night tariff, when the ‘Night Tariff’ is

selected, or use of pre-learned schedule of water consumption during

the week, when the ‘Consumption schedule’ is selected.

When the ‘Seasonal’ switch is activated it allows for extra heating of water

during cold season. This option compensates the need for more hot water

during winter due to the lower temperature of cold water and more heat

losses due to colder environment and walls in the room where the water

heater is installed. It is recommended to turn on that switch.

The ‘Operation Mode’ field is under the ‘Seasonal’ switch. Fine adjustment

of the temperature is carried out through it when priority is given to ‘Night

Tariff’. The more economical the mode, the lower the temperature of water

heating. Possible alternatives are ‘Eco Heating’, which is the most

economical mode, and ‘Normal Heating’ and ‘Powerful Heating’.

The EN 814 switch has an effect in ’Consumption Schedule’ priority only. It

coordinates more completely the controller operation with the requirements

of EN 814/2013 Directive that is applicable to the water heater. Since that

directive stipulates requirements for achievement of higher minimum

temperatures than those required for normal operations that will surely

increase heat losses. It is recommended to turn off that switch.

џNew WiFi network (12) – initializes the WiFi module, if installed, to

switch to Access Point (AP) mode, by which the thermoregulator can

be connected to a WiFi network. With the pressing of (VIII) button the

modem will switch to Access Point mode, which means that it will

create a new WiFi network. The controller will show a display with the

name of the network and will read ‘Successful!’ when the network is

completely ready (13). Following the creation of a new WiFi network

the module may be connected to a phone, tablet or PC that will

connected the module to an Internet network to enable the remote

control and monitoring of the appliance operation. This is described in

the additional booklet provided in the packaging of the appliance

package.

OPERATION MODES - FIG. 7

The selection of an operation mode is made by pressing button (I), which

calls menu (1). The appropriate mode is selected by ▲ or ▼ buttons, and

the selection is confirmed by (VIII) button. Five seconds after a button is last

pressed, the mode selection menu is exited without changing the mode.

ATTENTION! ‘Timers’ mode cannot be selected, if there is no at least

one timer activated and the clock is not set to correct time. Smart Control

and Self-learning modes cannot be selected, if the clock is not set to

correct time.

‘Standby’ mode (2)

It turns off all active operations of the water heater. In this mode, only the

Anti-freezing mode and the Delayed start option are maintained.

‘Heating’ mode (3)

The thermoregulator will heat the water up to the preset temperature. The

temperature is set by pressing button (X). The preset temperature is

displayed in the middle of the screen. Subsequent pressing of buttons

changes the setting as desired. If no button is pressed by 10 seconds, the

new setting will be saved and the main screen is displayed. If you hold any of

▲ or ▼ buttons longer than 0.7 sec, the value of the preset temperature will

be automatically increased or decreased with a rate of 4 units per second.

Temperature control limits are 35-75°C (12).

NOTE! While the water heater is in this mode, there is an option for

forced water heating to the maximum temperature (POWERFUL

submode) by pressing and holding (XI) button for more than 2 sec. (8) In

this submode, the two heating elements will operate irrespective of the

status of ‘Fast Hearing’ switch in ‘System Settings’ menu. Forced water

heating will turn off automatically when the two water tanks are heated up

to the required temperature. Then, it will be proceeded to normal mode

operation.

Smart Control mode (4)-(9)

Automatically determines the temperature to which water is heated up at

any moment. The purpose is to ensure sufficient quantity of hot water where

it is necessary. Where no hot water is necessary, heating will be minimal in

order to reduce energy costs. There are two options. The setting for the

heating method is made in ‘Smart Control’ submenu of the main menu,

‘Priority’ line.

џHeating with learning user consumption habits and weekly hot

water consumption schedule. Mode repeated every subsequent

week. When selecting ‘Consumption Schedule’ priority, you need to

activate the ‘Self-learning’ mode through ‘Mode Selection’ menu (1).

Then, for seven full days, the water heater will monitor and save the

time for using hot water and its quantity. Upon passing the self-

learning cycle water will be heated up to a higher temperature, saved

hot water consumption data. During other periods a minimum

temperature of 40оC will be maintained. To make full use of the energy

saving options of this method, you need to use hot water in similar

times and quantities as during self-learning. Variation in time of hot

water use of more than half an hour and/or using a different quantity of

hot water than that during the self-learning period will result in reduced

energy savings.

NOTE! If ‘Smart Control’ mode is activates with ‘Consumption Schedule’

priority and the full seven-day self-learning cycle has not yet passed, it

will be started automatically (6). When the self-learning cycle is

completed, it will automatically proceed to ‘Smart Control’ mode with

‘Consumption Schedule’ priority.

џHeating with using a second ‘cheap’ electricity tariff. When

selecting the ‘Night Tariff’ priority (5), the advantages of the lower

EN EN

TTulpe Smart Master DU080 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info