Bedienungsanleitung Tunturi Cardio Fit T10 - 2020 (Seite 14 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

736481

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

English

To start the equipment:

- Insert the mains plug into the equipment.

- Insert the mains plug into the wall socket.

- Set the master power switch to the on position.

To stop the equipment:

- Set the mains power switch to the off position.

- Remove the mains plug from the wall socket.

- Remove the mains plug from the equipment.

Safety key (Fig F-4)

The equipment is equipped with a safety key that must be properly

inserted into the slot on top of the handrail to start the equipment.

If you remove the safety key from the slot, the equipment will stop

immediately.

- Insert the safety key into the slot on top of the handrail.

- Make sure that the clip of the safety key is properly attached to

your clothing.

- Make sure that the clip is not removed from your clothing before

the safety key is removed from the handrail.

‼ NOTE

• Console will show ---- -- --- when safety key is not in (correct)

position during start up.

Circuit breaker (Fig. E-2B)

The equipment is equipped with a circuit breaker that interrupts the

circuit when the electricity load is above the maximum capacity. When

this occurs, the circuit breaker must be pressed.

⚠ WARNING

• Before pressing the circuit breaker, remove the mains plug from

the equipment.

If the equipment shuts down, proceed as follows to restart the

equipment:

- Remove the mains plug from the equipment.

- Press the circuit breaker to restart the equipment.

- Insert the mains plug into the equipment.

‼ NOTE

• Some circuit breakers used in homes are not rated for high

inrush currents that can occur when a treadmill is first turned

on or even during normal use. If your treadmill is tripping the

circuit breaker (even though it is the proper current rating and

the treadmill is the only appliance on the circuit) but the circuit

breaker on the treadmill itself does not trip, you will need

to replace the breaker with a high inrush type. This is not a

warranty defect. This is a condition we as a manufacture have no

ability to control.

Folding & Unfolding the equipment.

‼ NOTE

• Before folding or unfolding the equipment, make sure the

remote control is taken out the holder to avoid it from falling

out.

• The both clamp levers ( #8) can be pulled out, and freely

repositioned without tightening, or loosen the fixture.

Release the clamp levers ( #8) and turn to adjust the fixation.

Unfolding the equipment (fig. F1)

- A-When being in vertical storage position

- While supporting the treadmill frame, loosen stabilizer frame

fastening knob (#43) on the RH side of the stabilizer frame ( #42) by

turning it in counter-clockwise direction.

- Tilt the mainframe slightly forwards and fold in the stabilizer frame.

- While supporting the treadmill frame, fasten stabilizer frame

fastening knob (#43) on the RH side of the stabilizer frame ( #42) by

turning it in clockwise direction.

- Lower the upright positioned treadmill in the horizontal position.

- B-When being in horizontal storage position.

- Turn both clamps levers ( #8) in the counter-clockwise direction to

loosen the fixation of the handrail.

- Tilt the handrail in the upright position. ( slightly forward angle )

- Turn both clamps levers ( #8) in the clockwise direction to fixate the

fixation.

- Trainer is now in ready-to-use position.

Refer to the illustrations for the correct way of unfolding the

equipment.

Folding the equipment (fig. F2)

- A-When being ready-to-use position

- Turn both clamps levers ( #8) in the counter-clockwise direction to

loosen the fixation.

- Guide the handrail in the downwards horizontal position.

- Turn both clamps levers ( #8) in the clockwise direction to fixate the

fixation of the handrail.

- Trainer is now in horizontal storage position.

- B-When being in horizontal storage position.

- Tilt the treadmill frame in the upright position by lifting it on the

mainframe ( Do not lift the treadmill by holding the handrail ).

- While supporting the treadmill frame, loosen stabilizer frame

fastening knob (#43) on the RH side of the stabilizer frame ( #42) by

turning it in counter-clockwise direction.

- Tilt the mainframe slightly forwards and unfold in the stabilizer

frame.

- While supporting the treadmill frame, fasten stabilizer frame

fastening knob (#43) on the RH side of the stabilizer frame ( #42) by

turning it in clockwise direction.

- Treadmill is now in vertical storage position. .

Refer to the illustrations for the correct way of folding the equipment.

Console (fig. E-1)

⚠ CAUTION

• Keep the console away from direct sunlight.

• Dry the surface of the console when it is covered with drops of

sweat.

• Do not lean on the console.

• Only touch the display with the tip of your finger. Make sure that

your nails or sharp objects do not touch the display.

‼ NOTE

• The console switches to standby mode when the equipment is

not used for 10 minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi Cardio Fit T10 - 2020 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info