Bedienungsanleitung Tunturi FitCross 40 (Seite 25 von 60) (Deutsch, Englisch, Holländisch, Französisch)

738069

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

English

- Set tension level for first of 20 colums, and confirm

with MODE to set second level, repeat this for all

colums.

- Press and hold MODE button for 2 seconds to

confirm program setting.

- Press START/ STOP key to start workout.

Press START/STOP key to pause workout.

- Use RESET to go back to main menu.

H.R.C. mode.

- Use UP/ DOWN key to select workout program,

choose H.R.C. mode and press mode key to enter

next setting entry for H.R.C. mode program.

- Use UP/ DOWN key to set age.

- Use UP/ DOWN key to select 55%, 75%, 90% or

TAG (Target H.R. _ Default 100)

- Use UP/ DOWN key to set time, press MODE to

confirm.

- Press START/ STOP key to start workout

- Use RESET, to go back to main menu.

Watt Mode.

- Use UP/ DOWN key to select workout program,

choose WATT and press MODE / ENTER key to

enter next setting entry for WATT mode program.

- Use UP/ DOWN to set WATT target.

(default: 120Watt)

- Use UP/ DOWN key to set TIME.

- Press START/ STOP key to start workout.

Use UP/ DOW) to adjust target Watt level.

- Press START/STOP key to pause workout.

- Use RESET to go back to main menu.

Recovery

- The RECOVERY key will only be valid if pulse is

detected.

- TIME will show „0:60“ (seconds) and counts down

to 0.

- Computer will show F1 to F6 after the countdown

to test heart rate recovery status. User can find the

heart rate recovery level based on the chart below.

- Press RECOVERY key again to return to the

beginning.

F1 Outstanding

F2 Excellent

F3 Good

F4 Fair

F5 Below average

F6 Poor

Body Fat

- Press the BODY FAT key to start body fat

measurement.

- During measuring, users have to hold both hands

on the hand grips. LCD display “-” “- -” “- - -” “- - -

-” for 8 seconds until computer finish measuring.

- LCD will display BMI and FAT %.

Body fat mode error codes

- *E-1

There is no heart rate signal input detected.

- *E-4

Occurs when FAT% and BMI result is below 5 or

exceeds 50.

Trouble shooting:

- If there is no signal when you pedal, please check if

the cable is well connected.

NOTE

• When stop training for 4 minutes, the main

screen will be off.

• If the computer displays abnormally, please re-

install the transformer and try again.

Cleaning and maintenance

The equipment does not require special maintenance.

The equipment does not require recalibration when

it is assembled, used and serviced according to the

instructions.

WARNING

• Do not use solvents to clean the equipment.

• Clean the equipment with a soft, absorbent cloth

after each use.

• Regularly check that all screws and nuts

are tight.

• If necessary, lubricate the joints.

Defects and malfunctions

Despite continuous quality control, defects and

malfunctions caused by individual parts can occur in the

equipment. In most cases, it will be sufficient to replace

the defective part.

- If the equipment does not function properly,

immediately contact the dealer.

- Provide the model number and the serial number of

the equipment to the dealer. State the nature of the

problem, conditions of use and purchase date.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi FitCross 40 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info