Bedienungsanleitung Tunturi FitRace 40 HR (Seite 16 von 40) (Deutsch, Englisch, Holländisch, Französisch)

736353

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

NOTE

• The console switches to standby mode when the

equipment is not used for 4 minutes.

Explanation Display functions

RPM

Display the rotations per minute.

Range: 0 ~ 999 RPM.

Without any signal being transmitted into the monitor

for 4 seconds during workout, RPM will display “0”

Time

Automatically accumulates workout time when

exercising.

Display range: 00:00 ~ 99:59.

Speed

Displays current training speed.

Range 0.0 ~ 99.9 / Units: KM/H.

Without any signal being transmitted into the monitor

for 4 seconds during workout, RPM will display “0”.

Distance

Automatically accumulates the distance from exercise

when exercising.

Range 0.0 ~ 999.9 / Units: KM.

Calories

Automatically accumulates calories burnt when

exercising.

Range: 0 ~ 9999 / Units: K.Cal.

NOTE

• This data is a rough guide for comparison of

different exercise sessions which cannot be used

in medical treatment

Pulse

- Current pulse will display after 6 seconds when

detected by the console.

- Without any pulse signal for 6 seconds, console will

display “P”.

- Pulse alarm will sound when current pulse is over

the target pulse.

- Range: 0-30 ~ 230 BPM.

Explanation of buttons

Mode/ Reset

- Press Mode/ Reset button to select console

functions.

- Push and hold for 3 seconds in, stop Mode/ Reset,

to reset: Time, Distance, Calories.

Opperation

Power on

- Press any key to power on the console when being

in sleep mode..

- Start pedalling to power on the console when being

in sleep mode.

Power off

Without any signal being transmitted into the monitor

for 4 minutes the monitor will enter SLEEP mode

automatically. ( Active training data will be lost )

Workout setting

- Press MODE/ RESET key to select the function of

TIME, DISTANCE, CALORIES, and PULSE. Use SET

key for setting and press MODE/ RESET key for

confirmation.

- For instance the time set-up, when the time value

is blinking, you can use UP and DOWN (DIAL) to

adjust the number. Press SET key for confirmation

and skip to next set-up. The set-up of DISTANCE,

CALORIES and PULSE is the same as TIME set-up.

- Once the workout begins and the console picks up

the exercise signal, the value of SPEED, RPM, TIME,

DISTANCE and CALORIES will count up on the

display.

- If a target is set for a specific value, that value will

countdown, till target is reached.

Cleaning and maintenance

The equipment does not require special maintenance.

The equipment does not require recalibration when

it is assembled, used and serviced according to the

instructions.

WARNING

• Do not use solvents to clean the equipment.

• Clean the equipment with a soft, absorbent cloth

after each use.

• Regularly check that all screws and nuts

are tight.

• If necessary, lubricate the joints.

Defects and malfunctions

Despite continuous quality control, defects and

malfunctions caused by individual parts can occur in the

equipment. In most cases, it will be sufficient to replace

the defective part.

- If the equipment does not function properly,

immediately contact the dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi FitRace 40 HR Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info