Bedienungsanleitung Tunturi Pure Treadmill 3.1 (Seite 13 von 68) (Deutsch, Englisch, Holländisch, Französisch)

615442

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

OWNER’S MANUAL

•

PURE RUN 3.1

normal position. Use treadmill for

your training session. Or allow the

treadmill to run for at least 5 minutes

at 5 KM/H (3 Mile/H).

NOTE!

Lubricate your treadmill only with T-Lube

S silicon lubricant. Contact your local

Tunturi distributor for further supplies

of T-Lube or further information on

lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and

make adjustments as needed. The belt

should run in the center of the treadmill.

Alignment is not usually needed,

provided

• The treadmill is placed on an even,

solid and horizontal surface and the

belt is correctly tensioned

• The alignment of the belt is correct

It is, however, possible for the belt

to be pushed to one side due to the

user’s running style (e.g. more weight

on one foot). The alignment of the

belt is adjusted by turning the two

bolts at the back of the treadmill.

ALIGN THE BELT ACCORDING TO

THE FOLLOWING INSTRUCTIONS:

1. Turn the power switch on and

increase the treadmill’s speed to 5

km/h (3 mph).

2. If the belt drifts to the left, turn the left

adjustment bolt 1/4 turn clockwise

and the right adjustment bolt 1/8

turn anti-clockwise. If the belt drifts

to the right, turn the right adjustment

bolt 1/4 turn clockwise and the left

adjustment bolt ¼ turn anti-clockwise.

3. If the belt remains centered the

adjustment is correct. If not, continue

to make small adjustments as above

until the belt is correctly aligned.

If the belt is allowed run across to

one side for long periods of time the

edges of the belt may be damaged

and the treadmill may not continue to

operate correctly. Any damage to the

belt caused by the lack of necessary

adjustment will not be covered by the

warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins

to slip on the rollers. In normal use,

however, keep the belt as loose as

possible! The belt tension is adjusted

by turning the same screws as used for

aligning the running belt. If turning the

screws will not effect the belt tension,

please contact your local Tunturi dealer.

1. Increase the treadmill’s speed to 5

km/h (3 mph).

2. Turn both adjustment screws an

equal amount, ¼ turn clockwise.

3. Try to slow the belt down by holding

onto the handrails and braking as

you walk (as if you were walking

downhill).

If the belt slips, turn another 1/4 turn and

repeat the test. When braking heavily the

belt may slip. If the belt keeps slipping

despite repeated adjustments, please

contact your local Tunturi dealer.

power switch on to reset the treadmill.

This should clear incidental errors and

ready the treadmill for normal operation

again. If after you have reset the

treadmill by turning the power switch off

and on again, and the treadmill is still not

operational, contact your local Tunturi

dealer for service.

If you require spare parts, always

give the model, serial number of your

equipment and the spare part number

for the part you need. The spare part list

is at the back of this manual. Use only

spare parts mentioned in the spare part

list.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi Pure Treadmill 3.1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info