Bedienungsanleitung Tunturi Star Fit B100 (Seite 18 von 52) (Deutsch, Englisch, Holländisch, Französisch)

738064

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

English

- Press and hold START/ STOP key for over 2 seconds

to reset console and to go back to main menu.

(Active training data will be lost )

H.R.C. mode. (Program 12)

- Use UP/ DOWN key to select Program 12 and press

ENTER to confirm.

- Use UP/ DOWN key to set TIME,

Range: 0:00 - 1:00 ~ 99:00 ±1:00

confirm setting by pressing ENTER.

- Use UP/ DOWN key to set DISTANCE,

Range: 00.00 - 00.10 ~ 99.90 ± 00.10

confirm setting by pressing ENTER.

- Use UP/ DOWN key to set CALORIES,

Range: 0.0 - 1.0 ~ 999.0 ± 1.0

confirm setting by pressing ENTER.

- Use UP/ DOWN key to set PULSE limit

Range: 0 - 60 ~ 220 ± 1

confirm setting by pressing ENTER.

NOTE

• When setting more than one goal, the training

will end at first achieved goal.

• Continue the workout by pressing START/ STOP

button, and training will end again at first next

achieved goal.

• Leave a goal blank and it will not be seen as a

pre-set limit.

• Set Pulse limit is resistance control function,

Resistance will auto lower when value is over

pulse target, and auto upper when under pulse

target.

- Press START/ STOP key to start workout

- Use UP/ DOWN key to adjust resistance level.

Load level is shown in LEVEL window.

- Press START/ STOP key to pause workout.

- Press and hold START/ STOP key for over 2 seconds

to reset console and to go back to main menu.

(Active training data will be lost )

Recovery

- The RECOVERY key will only be valid if pulse is

detected.

- TIME will show „0:60“ (seconds) and counts down

to 0.

- Computer will show F1 to F6 after the countdown

to test heart rate recovery status. User can find the

heart rate recovery level based on the chart below.

- Press RECOVERY key again to return to the

beginning.

F1 Outstanding

F2 Excellent

F3 Good

F4 Fair

F5 Below average

F6 Poor

Trouble shooting:

- If there is no signal when you pedal, please check if

the cable is well connected.

NOTE

• When stop training for 4 minutes, the main

screen will be off.

• If the computer displays abnormally, please re-

install the transformer and try again.

Cleaning and maintenance

The equipment does not require special maintenance.

The equipment does not require recalibration when

it is assembled, used and serviced according to the

instructions.

WARNING

• Do not use solvents to clean the equipment.

• Clean the equipment with a soft, absorbent cloth

after each use.

• Regularly check that all screws and nuts

are tight.

• If necessary, lubricate the joints.

Defects and malfunctions

Despite continuous quality control, defects and

malfunctions caused by individual parts can occur in the

equipment. In most cases, it will be sufficient to replace

the defective part.

- If the equipment does not function properly,

immediately contact the dealer.

- Provide the model number and the serial number of

the equipment to the dealer. State the nature of the

problem, conditions of use and purchase date.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi Star Fit B100 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info