Bedienungsanleitung Tunturi T70 loopband (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

542704

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

training session. Check the lubrication as follows:

1. Ensure the treadmill is powered off! Step on the treadmill

belt .and stand steadily where you normally run on the

belt.

2. Take hold of the horizontal handlebar and push the

belt with your feet so that it slides back and forth. The belt

should move softly and evenly, without a sound.

3. If you notice jerky movement or if the belt will not slide

check for lubrication by sliding your hand under the belt.

Lubricate the running deck according to the following

instructions:

1. Fold up the running deck and lock it.

2. Cut off the tip of the bottle cap.

3. Position the lubricant bottle between the belt and the

board

4. Try to reach the bottle as far into the center of the

running belt as possible and point the tip of the bottle

towards the running belt.

5. Squeeze the lubricant bottle to dispense half of the

bottle.

6. Move the running belt half of a revolution and repeat

steps 4 and 5.

7. Fold down the running deck into it’s normal position. Use

treadmill for your training session or allow the treadmill to

run for at least 5 minutes.

ALIGNING THE RUNNING BELT

adjustments as needed. The belt should run in the

center of the treadmill. Alignment is not usually

needed, provided

• the treadmill is placed on an even, solid and

horizontal surface and the belt is correctly tensioned

• the alignment of the belt is correct

It is, however, possible for the belt to be pushed to

one side due to the user’s running style (e.g. more

weight on one foot). The alignment of the belt is

adjusted by turning the two bolts at the back of the

treadmill.

ALIGN THE BELT ACORDING TO THE FOLOWING

INSTRUCTIONS:

1. Turn the power switch on and increase the

treadmill’s speed to 5 km/h (3 mph).

2. If the belt drifts to the left, turn the left

adjustment bolt 1/4 turn clockwise and the right

adjustment bolt 1/8 turn anti-clockwise. If the belt

drifts to the right, turn the right adjustment bolt 1/4

turn clockwise and the left adjustment bolt ¼ turn

anti-clockwise.

3. If the belt remains centered the adjustment is

correct. If not, continue to make small adjustments

as above until the belt is correctly aligned. If the belt

is allowed run across to one side for long periods of

time the edges of the belt may be damaged and the

treadmill may not continue to operate correctly. Any

damage to the belt caused by the lack of necessary

adjustment will not be covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on

the rollers. In normal use, however, keep the belt

as loose as possible! The belt tension is adjusted by

turning the same screws as used for aligning the

running belt. If turning the screws will not effect the

belt tension, please contact your local Tunturi dealer.

1. Increase the treadmill’s speed to 5 km/h (3 mph).

2. Turn both adjustment screws an equal amount, ¼

turn clockwise.

3. Try to slow the belt down by holding onto the

handrails and braking as you walk (as if you were

walking downhill). If the belt slips, turn another

1/4 turn and repeat the test. When braking heavily

the belt may slip. If the belt keeps slipping despite

repeated adjustments, please contact your local

Tunturi dealer.

MALFUNCTIONS

NOTE! Despite continuous quality control, defects

and malfunctions caused by individual components

may occur in the equipment. In most cases it’s

unnecessary to take the whole device in for repair,

as it’s usually sufﬁ cient to replace the defective

part. Always give the model, serial number of

your equipment and in case of malfunctions also

conditions of use, nature of malfunction and any

error code.

When you encounter unusual behavior from the

treadmill, simply turn the power switch off, wait 1

minute and turn the power switch on to reset the

treadmill. This should clear incidental errors and

ready the treadmill for normal operation again. If

after you have reset the treadmill by turning the

power switch off and on again, and the treadmill

is still not operational, contact your local Tunturi

dealer for service.

If you require spare parts, always give the model,

serial number of your equipment and the spare part

number for the part you need. The spare part list

is at the back of this manual. Use only spare parts

mentioned in the spare part list.

ERROR CODES

The user interface will display information about

operational faults.

E1: Speed sensor error. Unplug the electrical cord

from the wall outlet and from the treadmill, wait

1 minute and turn the power switch on again. If

treadmill recovers to normal operation, you may

continue to use the treadmill. Otherwise, call the

dealer for service.

E6, E7: Lift motor error. Unplug the electrical cord

from the wall outlet and from the treadmill, wait

1 minute and turn the power switch on again. If

treadmill recovers to normal operation, you may

continue to use the treadmill. Otherwise, call the

dealer for service.

PROTECTIVE CIRCUIT

The machine will shut off when the electricity

load is above the machine’s capacity. To restart the

machine, please follow the procedure below:

A. Unplug the power cord from the machine’s

socket.

B. Push in the safety switch.

C. Replug the power cord into the machine’s socket.

Tunturi T70 loopband Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info