Bedienungsanleitung Turbionaire Senso 13 - Wifi (Seite 12 von 116) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

804598

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

MODE

Auto mode - Continuously drying mode – Sleeping mode cycle, press once to

switch the mode from one to another, the corresponding indicator lights up.

•Auto mode: when environmental humidity ≥ set humidity 3%, the fan starts working and

compressor starts working after 3 seconds. When environmental humidity ≤ set humidity

-3%, the compressor stops working and fan stops working after 30 seconds’ delay. Both

fan speed and humidity can be adjusted under auto mode.

•Continuously drying mode: The machine continues to run, but the humidity cannot be

adjusted.

•Sleeping mode: Touch the sleep button, the button lights up and start the sleep

function. If the control panel is not operated within 10 seconds, all indicators turns dark

gradually and the fun speed is automatically switched from high to low. Touch any

button to wake up the SLEEP Mode indicator. Touch MODE button again to exit the SLEEP

mode.

When environmental humidity ≤ 57%，compressor stops working and the fan shut down

after 30 seconds’ delay.

When environmental humidity ≥ 63%，the fan starts working and compressor starts

working after 3 seconds.

Fan speed and humidity cannot be adjusted under SLEEP mode.

TIMER

Press the timer button to set the 0-24 hour timing function. The interval is 1

hour. Each time you press this button, the value increased 1 hours and then the

corresponding timing value is displayed on the screen. The setting value is “00” to cancel

the timer function. The indicator turns out. After the timer is set and completed, the timer

LED is on during the timing period. After the timing is over, the timer LED turns off

automatically. In the running state, set the time to turn off the machine;

In the standby state, set the time to turn on the machine.

HUMIDITY SET

Touch the humidity button (HUM SET) to check the current environment humidity,

touch this button again and you can set the humidity. The range of target humidity is 30%-

35% - 40% - 45% - 50% - 55%- 60% - 65% -70% - 75%- 80%. After setting 3 seconds,

the system confirms the input value and then the machine exits the setting state, and

returns the current humidity. In the drying mode, the target humidity cannot be changed.

Long Press humidity button for 3 seconds to display the current ambient temperature.

FAN SPEED (SPEED)

High wind - low wind cycle, press button once to switch and then the corresponding

LED indicator lights up. In continuously drying mode, sleep mode and defrosting period, the

wind speed cannot be changed.

POWER

In the standby state, press the power button to turn on, the operation indicator

lights up and the default fan speed is high, and the default humidity is 50%. In the

power-on state, press the power button to turn off, the running indicator light goes off and

the compressor stops immediately, and then the fan shut down after 30 seconds delay.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Turbionaire Senso 13 - Wifi Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info